Denon AVR-4806CI Owners Manual - Page 45

Ext. In, Phones

Page 45 highlights

Playback using the external input (EXT. IN) terminals Press the EXT. IN button on the main unit or INPUT MODE button on the remote control unit to switch the external input. When operating the remote control unit: Basic Operation Turning the sound off temporarily (MUTING) • Use this to mute the audio output temporarily. Press the MUTE button. You can adjust the muting level ( page 118). (Remote control unit) The mode switches as shown below each time the INPUT MODE button is pressed: AUTO PCM DTS EXT.IN ANALOG • Cancelling MUTING mode: Press the MUTE button again, or press the VOLUME button on the remote control, or adjust the volume up or down via the front panel VOLUME knob. • Cancelling the external input mode: Press the INPUT MODE or ANALOG button to switch to the desired input mode ( page 47). • The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. • If the subwoofer output level seems too high, set the "SW ATT" surround parameter to "ON". NOTE: • When the input mode is set to the external input (EXT. IN), the surround mode (DIRECT, STEREO, HOME THX CINEMA, STANDARD, 7CH STEREO, WIDE SCREEN or DSP SIMULATION) cannot be set. • In play modes other than the external input mode, the signals connected to these terminals cannot be played. In addition, signals cannot be output from channels not connected to the input terminals. Listening over headphone Connect the headphone to the PHONES jack. • The pre-out output (including the speaker output) is automatically turned off when headphones are connected. NOTE: • To prevent hearing loss, be careful not to raise the volume level excessively when using headphones. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202

45
Basic Operation
Playback using the external input (EXT. IN)
terminals
Press the
EXT. IN
button on the main unit or
INPUT
MODE
button on the remote control unit to switch
the external input.
When operating the remote control unit:
Cancelling the external input mode:
Press the
INPUT MODE
or
ANALOG
button to switch to the
desired input mode (
page 47).
The external input mode can be set for any input source. To
watch video while listening to sound, select the input source
to which the video signal is connected, then set this mode.
• If the subwoofer output level seems too high, set the “SW
ATT” surround parameter to “ON”.
NOTE:
When the input mode is set to the external input (EXT. IN),
the surround mode (DIRECT, STEREO, HOME THX
CINEMA, STANDARD, 7CH STEREO, WIDE SCREEN or
DSP SIMULATION) cannot be set.
• In play modes other than the external input mode, the
signals connected to these terminals cannot be played. In
addition, signals cannot be output from channels not
connected to the input terminals.
Connect the headphone to the
PHONES
jack.
• The pre-out output (including the speaker output) is
automatically
turned
off
when
headphones
are
connected.
NOTE:
To prevent hearing loss, be careful not to raise the volume
level excessively when using headphones.
Listening over headphone
Press the
MUTE
button.
You can adjust the muting level (
page 118).
Turning the sound off temporarily
(MUTING)
Use this to mute the audio output temporarily.
Cancelling MUTING mode:
Press the
MUTE
button again, or press the
VOLUME
button on
the remote control, or adjust the volume up or down via the
front panel
VOLUME
knob.
AUTO
EXT.IN
ANALOG
PCM
DTS
The mode switches as shown below each time the
INPUT MODE
button is pressed:
(Remote control unit)