Denon DCM-460 Operating Instructions - Page 18
LL:Ii
View all Denon DCM-460 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
ENGLISH REMOTE CONTROL UNIT RC-246 (DCM-460) Repeat button (REPEAT) Drawer Open/Close button (..1 OPEN/CLOSE) Track number buttons (1 - 10) +10 button Disc Number buttons (1-5) Automatic search reverse button ( 1H I Play button ( ) Pause button ( II ) Stop button ( • I Favorite Track File button (F. T. FILE-FILE) Manual search reverse button ( 44 r..2. 7c7:3 OPEN/ &CLOSE r -r - RE EAT Ell RAP DOM DIRECT o 01 U 9 10 aJ • 0 CALL r 41 DISC 1 DISC 2 01 3 " .0 SC il mi• .. DISC 5 ±liSC SKIP LL:Ii I IM PLAY 1 :3 EP + I Awls pm. VOLUME. LEI -E3 L + .1 II STOP ',CLEAR TIME E43 43 DENION ' RC•246 Setting to the Program Mode • For program search, press the PROG/DIRECT button then the track number buttons (1 through 10 and +10). • The remote control unit is normally set to the direct mode. Random button (RANDOM) Program/Direct button (PROG/DIRECT) Call button (CALL) Disc Skip - button (DISC SKIP - ) Disc Skip + button (DISC SKIP + Automatic search forward button ( ) Volume buttons (VOLUME) Time button (TIME) Favorite Track File Clear button (F. T. FILE-CLEAR) Manual search forward button ( N I Use this to adjust the output level output of the VARIABLE. The volume increases when the (+1 button is pressed, decreases when the (-) button is pressed. • Direct Selection Normally, direct search is possible simply by pressing the desired number buttons. • Program Selection (During playback, the track which is currently playing is programmed as the 1st track.) Press the PROG/DIRECT button, then press the number buttons. For example, to program tracks number 3, 11, and 5, press PROG/DIRECT -• 3 - +10 and 1 -+ 5. To cancel the program, press the PROG/DIRECT button. • Inputting the Track Numbers For track numbers below 10, simply press the corresponding button. For track numbers of 11 and greater, press the +10 then the number buttons. For example, for track number 22 press +10 twice then 2. • Volume The volume control on the unit will operate when the volume buttons are pressed. The volume can be checked by looking at the position of the control. • Skipping Discs The Disc Skip button (DISC SKIP +, - ) will not function in the random and program modes. During disc sequential random playback, when the Disc Skip + button is pressed, the following disc is played in random order. • Volume The output level of the VARIABLE output terminal can be changed. When the volume button is pressed, " - " appears in the TIME M (minutes) section of the display window and the level appears in the S (seconds) section. The volume can be changed between a maximum of "0" and a minimum of "-50" in 50 steps, by approximately 1.5 dB per step. 18 • The Time indicator indicates the amount of elapsed time for the track currently being played, the amount of time remaining for the current track and the amount of time remaining for all tracks yet to be played. Normally, the amount of elapsed time for the current track is displayed. Pressing this button once causes the SINGLE indicator to light up, displaying the amount of time remaining for the current track. Pressing the button once more turns the SINGLE indicator off and causes the TOTAL indicator to light up, displaying the time remaining for all tracks yet to be played on the disc. Pressing the button once again turns the TOTAL indicator off and causes the indicator to display the elapsed time for the current track. • During playback, the total remaining time is the remaining time for the disc. For programmed playback, the remaining time for the program is only displayed when the programmed tracks are all on the same disc. In the case of 21st and subsequent tracks, the time remaining for one track is displayed "----". When 21st and subsequent tracks is programmed, the time remaining for all tracks is displayed. "-+7". ---" is displayed when tracks on more than one disc are programmed.