Denon DN S5000 Quick Start Guide - Page 22
Alpha-Track Hot Start mode, Hot start mode, Sampler, Moving Sampler B point
UPC - 081757505185
View all Denon DN S5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
ENGLISH Sampler DN-S5000 has two Samplers of 15 seconds length. These Samplers are also used in looping playback. i, !0 q, r, !0 w, o y, u e, t Record in Sampler q When the SAMP button (SAMP1 (A3) or SAMP2 (A4)) is pushed in the standby or playing, the sound from A3 1 or A4 point is recorded to Sampler memory up to 15 seconds. • The SAMP1 or SAMP2 button is flashing while recording. When the recording is completed, the button turns off and the corresponding SAMP B LED lights up. Setting B point w When the B button is pushed during Sampler recording, the Sampler Loop B point is set and the loop mode turns on. 2 • Recording continues for approximately 15 seconds without stopping after set B point. • If the B point is not set, recording end point set as B point automatically. Also EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically. Stop recording e To stop recording before SAMP. STOP recording finish 3 automatically with memory full, push the STOP (a CUE) button. • The EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically. Play Sampler sound r Playback of the Sampler sound starts when the SAMP button is pushed after recording has stopped. • Sampler playback continues in looping. With setting B point, playback loop between A and B point. Without B point 4 setting Sampler loops whole recorded length (about 15 seconds). NOTE: It is not possible to play Sampler1 and Sampler2 at the same time. SAMP. STOP t To stop the Sampler sound push STOP (a CUE) button. Select Sampler Loop mode You can select loop mode for Sampler when Sampler playback stop. Loop (default): Sampler playback continues with looping. (EXIT/RELOOP LED stays lit) 5 Exit: Sampler playback continues over B point up to recording length. (EXIT/RELOOP LED flashes) Single: Sampler playback stops at B point. (EXIT/RELOOP LED turned off) y To select loop mode, push EXIT/RELOOP button after recording and before playing. Exit and Reloop 6 u The EXIT/RELOOP button can be used same as Seamless Loop function. Reverse Play i You can play Sampler sound in reverse with push RVS (FLIP) 7 button. In reverse play mode RVS LED lights up. • Reverse playback will start with next playback starting after reverse mode turned on. Moving Sampler B point o When the B button is pushed during Sampler 8 playback, the B point moves to the point at which the button was pushed, and loop playback from point A starts. Setting the Sampler volume and pitch • The sound level (volume) and pitch can be 9 set individually for Sampler1 and 2. • See m - step 8 "Adjust sound level and pitch". Clearing the Sampler data !0 While pressing the (RVS)/FLIP/(CLR) button, push the SAMP button (SAMP1 or SAMP2) to clear the Sampler. 10 • By pushing the (RVS)/FLIP/(CLR) button for approx. 1 sec, you can clear both Samplers 1 and 2. # # # # Hot start mode Like with buttons A1 and A2, operation is performed using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP buttons. Operation is same as Hot Start with A1, A2 buttons. See page 16 for details. Alpha-Track Hot Start mode Like with buttons A1 and A2, operation is performed using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP buttons. (Refer to page 16.) 20