Denon DN S5000 Quick Start Guide - Page 25
PRESET, Preset mode, Preset items and data - platter
UPC - 081757505185
View all Denon DN S5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
14 PRESET 1. Preset mode q The preset mode is available when PRESET button is pushed for more than 1 sec while DN-S5000 is in Cue, pause or no disc mode. w Turn the PARAMETERS knob to select the preset item. e After selecting an item, push the PARAMETERS knob to select the preset data. r To change other Preset items, repeat these steps. t Push the PRESET, CUE or PLAY/PAUSE (13) button to exit from the Preset mode. 2. Preset items and data The "*" mark next to the data indicates the default value. (1) AUTO CUE : Auto Cue level search on/off. (ON* / OFF) (2) PITCH RANGE : Select the playing pitch range when the power is turned on. (±4 / ±10* / ±16 / ±24%) (3) ALPHA-TRACK OUTPUT : Alpha-Track playback output destination. (Main out* / Alpha out) (4) PLATTER : Select whether or not the Platter is to rotate during playback. (Turn round* / Turn stop) (5) PLATTER MODE MEMO : When the Platter mode (DRAG-S, BRAKE and ECHO) parameters, the source and the on/off setting are stored, the stored data is set each time the power is turned on. q To set the effect data, push the PARAMETERS knob and select "YES". • "Set OK?" flashes on the character display. w Push the PARAMETERS knob again and select "OK" to execute setting the data. e Once setting is completed, "Complete!" is displayed. (6) AUTO LOAD : Time for automatically loading disc. (OFF / 10 / 30 / 60* seconds) (7) EOM : Track end message start time. (OFF / 10* / 15 / 20 / 30 / 60 / 90 seconds) (8) DIGITAL OUT OUTPUT LEVEL : Select the digital out output level. (Normal* / -6 dB Down) NOTE: Use -6dB if the playback output is clipped when the Main and Alpha-Tracks are played simultaneously at the same position. (9) FADER START MODE: Select 2-line type (Cue and Play) or 1 line type (Play and Pause). (Play /Cue* / Play/Pause) (10) POWER ON PLAY : Playback starts when the power is turned on if a disc is loaded. (On / Off*) (11) A3/4 MODE : Select the A3 and A4 button operating modes when the power is turned on. (Sampler* / 4H/S / Alpha-Track H/S) (12) SINGLE/CONTINUOUS : Select the play mode when the power is turned on. (Single* / Continuous) (13) ELAPSED/REMAIN: Select the time mode when the power is turned on. (Elapsed* / Remain) (14) PROGRAM ALL CLEAR : Clear all program play data in the non-volatile memory. q To clear the program, push the PARAMETERS knob and select "YES". • "Clear OK?" flashes on the character display. w Push the PARAMETERS knob again and select "OK" to execute clearing the program. "Prog. Clear" is displayed on the character display while data clearing. e Once clearing is completed, "Complete!" is displayed. (15) MEMO ALL CLEAR : Clear all MEMO data in the non-volatile memory. q To clear all MEMO data, push the PARAMETERS knob and select "YES". • "Clear OK?" flashes on the character display. w Push the PARAMETERS knob again and select "OK" to execute clearing all MEMO data. • "Memo Clear" is displayed on the character display while clearing. e Once clearing is completed, "Complete!" is displayed. ENGLISH (16) MEMO ALL COPY : Copy all MEMO data from the master unit of DN-S5000 (or DN-D9000, DN-2600F) to the slave unit of DN-S5000 (or DN-D9000) when both unit are connected by the normal straight Cable. (See diagram for the cable.) NOTE: Be sure CD player have no discs inside. A straight cable used: X'EFFECT OUT DN-S5000 DN-S5000 (X'EFFECT IN) DN-D9000 (X'EFFECT) DN-2600F (X'EFFECT) • Using the straight cable, connect the X-EFFECT terminals between two DN-S5000 units or between one DN-2600F and one DN-S5000 unit or between one DN-D9000 and one DN-S5000 unit. • If a DN-2600F is the master unit, take the procedures below in the Preset mode of the DN-2600F beforehand. (For details, refer to the DN-2600F's operating instructions.) ✽ Set the "Copy Master" for the Preset item (14). Then, step to the q below on the slave unit of DN-S5000. • Copying can be performed using the DN-S5000 and DN-D9000 in the same way as when using two units of the DN-S5000. DN-S5000-1 DN-S5000-2 POWER ON OFF DIGITAL OUT IN LL MAIN RR OUT LINE OUT MONITOR X-EFFECT OUT jack X-EFFECT ALPHA MAIN FADER X-EFFECT ALPHA MAIN FADER POWER ON OFF DIGITAL OUT IN LL MAIN RR OUT LINE OUT MONITOR X-EFFECT IN jack 3.5 mm stereo mini cord • Perform the copying operation as below on the slave unit of DN-S5000. q To start copying, push the PARAMETERS knob and select "YES". Now "Copy OK?" messages flashes on the character display. w Push the PARAMETERS knob again to confirm. Now "Start OK?" is displayed. NOTE: If a DN-2600F is the master unit, take the procedures below in the Preset mode of the DN-2600F here. In the Preset item (15), first start copying on the DN-2600F. Then, step to e below on the slave unit of DN-S5000. e Push the PARAMETERS knob once again, and the unit starts copying when the MEMO data are received from the master unit. Now "Copying" is displayed. • If the master unit and the slave unit are not connected properly or the DN-2600F is not prepared to start sending data, "Not Connect" is displayed on the character display. r When copying is completed correctly, "Complete!" is displayed. • "Copy Error" is displayed on the character display if copying was not completed correctly. In this case, try the above procedure again. • The copied MEMO data are added to the highest number area of the slave DN-S5000 unit. (17) The DN-S5000's software version is displayed. (SYSTEM / DSP / CD DRIVE) (18) PRESET CLEAR : Set all the preset data back to the factory defaults. q To clear the PRESET data, push the PARAMETERS. "Initial OK?" flashes on the character display. w Push the PARAMETERS knob again and select "OK" to start clear the preset data. "Preset Int" is displayed on the character display while data clearing. e Once clearing is completed, "Complete!" is displayed. 23