Dewalt DXPW3625 Instruction Manual - Page 4

Engine - manual

Get Dewalt DXPW3625 PDF manuals and user guides View all Dewalt DXPW3625 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

English 4 Connect Spray Wand to Spray Gun Thread the spray wand into the end of the spray gun. 5 Connect QC Nozzles to Spray Wand Pull quick connect coupler back and insert nozzle. Release quick connect coupler and twist nozzle to make sure it is secure in coupler. 6 Turn Water Faucet Completely On Do not run the unit without water supply connected and turned on. Use Cold Water Only. 7 Release Air from System Release all air from pump and high pressure hose by depressing trigger until a steady stream of water is present. Approximately 30 seconds. 8 Verify the Engine Switch is turned to the ON Position OFF ON 30 S 10 Move the choke to the CLOSED position 11 Pull the Recoil Starter Grip Pull the recoil starter grip to start the engine. 9 Place the fuel valve lever in the ON position. 12 Move the choke to the OPEN position WARNING: This Guide is not a substitute for reading the operator's manual. User must read and understand operator's manual before using this product. Engine Refer to the engine instruction manual for location and operation of other engine controls. Pump The Pump was filled with oil at the factory. The preferred oil is SIMPSON® Premium Pump Crankcase Oil. If this oil is not available, an SAE 15W-40 oil may be used. Change the pump oil after the first 50 hours of operation and every 100 hours thereafter, or every 3 months. NOTICE: The pump was shipped with a shipping plug. The shipping plug MUST be removed and replaced with the dipstick or vented cap (supplied). Running the unit WITHOUT removing and replacing the shipping plug with the dipstick or vented cap (supplied) may cause damage to the pump and will void the warranty. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
ENGLISH
2
4
Connect Spray Wand to
Spray Gun
Thread the spray wand into the end of
the spray gun.
5
Connect QC Nozzles to
Spray Wand
Pull quick connect coupler back and
insert nozzle. Release quick connect
coupler and twist nozzle to make sure
it is secure in coupler.
6
Turn Water Faucet
Completely On
Do not run the unit without water
supply connected and turned on. Use
Cold Water Only.
7
Release Air from System
Release all air from pump and high
pressure hose by depressing trigger
until a steady stream of water is
present. Approximately 30 seconds.
8
Verify the Engine Switch is
turned to the ON Position
9
Place the fuel valve lever in
the ON position.
30 S
OFF
ON
10
Move the choke to the
CLOSED position
11
Pull the Recoil Starter Grip
Pull the recoil starter grip to start
the engine.
12
Move the choke to the
OPEN position
±
WARNING:
This Guide is not a substitute for reading the operator’s manual. User must read and understand operator’s
manual before using this product.
Engine
Refer to the engine instruction manual for location and operation of other engine controls.
Pump
The Pump was filled with oil at the factory. The preferred oil is SIMPSON® Premium Pump Crankcase Oil. If this oil is not
available, an SAE 15W-40 oil may be used. Change the pump oil after the first 50 hours of operation and every 100 hours
thereafter, or every 3 months.
NOTICE:
The pump was shipped with a shipping plug. The shipping plug MUST be removed and replaced with the
dipstick or vented cap (supplied). Running the unit WITHOUT removing and replacing the shipping plug with the dipstick
or vented cap (supplied) may cause damage to the pump and will void the warranty.