Home » E-Z-GO Manuals » Golf Carts » E-Z-GO RXV - Gas » Manual Viewer

E-Z-GO RXV - Gas Owner Manual - Page 30

Light Bulb Replacement

Get E-Z-GO RXV - Gas PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

OPERATION AND SERVICE INFORMATION Read all of manual to become familiar with this vehicle. Pay attention to all NOTICES, CAUTIONS, WARNINGS and DANGERS. B NOTICE Tire plug tools and plugs are available at most automotive parts outlets and have the advantage of not requiring the tire be removed from the wheel. If the tire is flat, remove the wheel and inflate the tire to the maximum recommended pressure for the tire. Immerse the tire in water to locate the leak and mark with chalk. Insert tire plug in accordance with manufacturer's instructions Valve Stem Cap . To reduce the possibility of severe injury, be sure the mounting/demounting machine is anchored to floor. Wear OSHA approved safety equipment when mounting/demounting tires. If the tire is to be removed or mounted, the tire changing machine manufacturer's recommendations must be followed in order to reduce possibility of severe injury. WHEEL INSTALLATION Tire style may vary To reduce the possibility of component damage, do not tighten lug nuts to more than 85 ft. lbs. (115 Nm) torque. NOTICE It is important to follow the 'cross sequence' pattern when installing lug nuts. This will assure even seating of the wheel against the hub. With the valve stem to the outside, mount the wheel onto the hub with lug nuts. Finger tighten the lug nuts in a 'cross sequence' pattern (Ref. Fig. 14). Tighten the lug nuts to 50 - 85 ft. lbs. (70 - 115 Nm) torque in 20 ft. lbs. (30 Nm) increments following the 'cross sequence' pattern.(Ref. Fig. 14) Cross Sequence Fig. 14 Wheel Installation Light Bulb Replacement To reduce the possibility of premature bulb failure, do not touch new bulbs with bare fingers. Use clean, dry tissue or paper towel to handle the glass portion of the bulb. HEAD LIGHT BULB REPLACEMENT Make sure that the vehicle key switch is in the 'OFF' position and the key has been removed. For vehicles equipped with lights mounted in the cowl, locate the headlight bulb socket on the backside of the light assembly. 1. Turn the headlight bulb (3) clockwise and pull to remove. 2. Disconnect the accessory harness (5) from the light bulb. Page 10 Owner's Guide

Section	Page
C_Model_Info-05Feb2010.pdf	3
E-Z-GO Division of TEXTRON Inc. is not liable for errors in this manual or for incidental or consequential damages that result from the use of the material in this manual.	3
These are the original instructions as defined by 2006/42/EC.	3
OWNER’S MANUAL AND SERVICE GUIDE	3
GASOLINE POWERED	3
FLEET GOLF CARS	3
RXV GOLF CAR	3
RXV FREEDOM™	3
RXV SHUTTLE 2 + 2	3
STARTING MODEL YEAR 2011	3
The use of non Original Equipment Manufacturer (OEM) approved parts may void the warranty.	4
BATTERY PROLONGED STORAGE	4
E_Operation_Service_Info1-28APR10.pdf	21
In order to obtain correct components for the vehicle, the manufacture date code, serial number and vehicle model must be provided when ordering service parts.	21
Fig. 1 Serial Number Location on Steering Column	21
Fig. 2 Serial Number on Front Frame	21
Fig. 3 Serial Number on Rear Frame	21
BEFORE INITIAL USE	22
.	22
Fig. 4 Initial Service Chart	22
CONTROLS AND INDICATORS	22
1. Key Switch	22
2. Fuel Gauge (optional)	22
3. Head Light Switch (optional)	22
4. Turn Signal Switch (optional)	22
5. Horn Button (optional)	22
6. Accelerator Pedal	22
7. Service Brake Pedal	22
8. Park Brake	22
Fig. 5 Operator Controls & Gauges	22
9. Hour Meter (optional)	22
10. Direction Selector	22
11. Choke	22
Fig. 6 Hour Meter	22
Key Switch	23
Direction Selector	23
Fig. 7 Direction Selector	23
Accelerator Pedal	23
Combination SERVICE Brake & Park Brake Pedal	23
Choke	23
Fig. 8 Choke	23
Fuel Gauge (IF SO EQUIPPED)	23
Low Oil Pressure Indicator (IF SO EQUIPPED)	23
Headlight Switch (IF SO EQUIPPED)	24
Turn Signal Switch (IF SO EQUIPPED)	24
Horn (IF SO EQUIPPED)	24
OPERATING THE VEHICLE	24
Run-In	24
The oil dipstick and cap must be in place before operating the engine. Failure to install the dipstick and cap will result in oil becoming contaminated and/or being discharged into the engine compartment.	25
Fig. 9 Oil Dipstick and Cap	25
Fig. 10 Check Oil Level	25
Cold Starting	25
Starting and Driving	25
Starting Vehicle On A Hill	26
Coasting	26
Fuel	26
Fig. 11 Fueling	26
Battery	27
Starting a Vehicle with a Discharged Battery	27
Labels and Pictograms	27
Sun Top And Windshield	27
VEHICLE CLEANING AND CARE	27
Vehicle Cleaning	27
REPAIR	28
Lifting The Vehicle	28
Fig. 12 Chock Wheels	28
T	29
Fig. 13 Lifting the Vehicle	29
WHEELS AND TIRES	29
Tire Repair	29
Tire plug tools and plugs are available at most automotive parts outlets and have the advantage of not requiring the tire be removed from the wheel.	30
.	30
Wheel Installation	30
It is important to follow the ‘cross sequence’ pattern when installing lug nuts. This will assure even seating of the wheel against the hub.	30
Fig. 14 Wheel Installation	30
Light Bulb Replacement	30
Head Light Bulb Replacement	30
1. Turn the headlight bulb (3) clockwise and pull to remove.	30
2. Disconnect the accessory harness (5) from the light bulb.	30
Fig. 15 Head Light Bulb Replacement	31
3. Connect the accessory harness (5) to the light bulb (3).	31
4. Align the bulb with the opening in the back of the headlight assembly.	31
5. Turn the bulb (3) counter clockwise until it stops.	31
Turn signal Bulb Replacement	31
1. Remove the phillips head screw (7) and turn the retaining collar (8) to align with the turn signal bulb housing (9).	31
2. Grip the turn signal bulb housing (9) and pull backward to remove housing from the headlight assembly.	31
Fig. 16 Turn Signal Bulb Replacement	31
3. Remove the bulb from the housing and replace with a new one.	31
4. Push turn signal housing (9) into headlight assembly firmly, making sure that it is seated completely.	31
5. Turn the retaining collar (8) to secure the bulb housing and install the phillips head screw (7) to secure in place.	31
Tail Light/Brake Light Bulb Replacement	31
1. Remove the two phillips head screws (8) that secure the lens (9) to the tail light assembly.	31
2. Remove the light bulb.	31
3. Install the new light bulb.	31
4. Install the lens (9) and secure in place with the two phillips head screws. (8)	31
Fig. 17 Tail and Brake Light Bulb Replacement	31
TRANSPORTING VEHICLE	31
Towing	31
Neutral Lock	32
.	32
Fig. 18 Neutral Lock	32
Hauling	32
SERVICE AND MAINTENANCE	33
PERIODIC SERVICE SCHEDULE	33
P - CHECK C&A - CHECK & ADJUST CL - CLEAN R - REPLACE	33
Fig. 19	33
CAPACITIES AND REPLACEMENT PARTS	35
Fig. 22 Torque Specifications and Bolt Grades	35
Tire Inspection	36
Rear Axle	36
Checking the Lubricant Level	36
Fig. 23 Add, Check and Drain Axle Lubricant	36
Checking the Oil Level	36
Fig. 24 Oil Dipstick & Cap	37
Fig. 25 Check Oil Level on Dipstick	37
When adding oil between oil changes, do not mix brands and viscosity grades of oil.	37
Changing the Oil	37
Fig. 26 Oil Viscosity Chart	37
Fig. 27 Cleaning Top of Engine	38
Fig. 28 Remove Oil Filter	38
Fig. 29 Inspect Oil Filter	38
Fig. 30 Oil Drain Plug	38
Fig. 31 Add Engine Oil	39
The oil dipstick and cap must be in place before operating the engine. Failure to install the dipstick and cap will result in oil being discharged into the engine compartment.	39
AIR CLEANER INSPECTION and REPLACEMENT	39
The air cleaner unit on the vehicle is a dry unit. DO NOT use oil on the filter element or any part of the unit.	39
Fig. 32 Air Cleaner	39
Cleaning the Air Filter Element	39
Fig. 33 .Air Cleaner Assembly	39
A loose belt can cause audible vibration and squeal.	40
Fig. 34 Checking Belt Tension with Gauge	40
Fig. 35 Checking Belt Tension with Finger	40
Adjusting the Belt	40
Fig. 36 Adjusting the Belt Tension	40
COOLING SYSTEM CLEANING	40
Fig. 37 Cleaning Cooling System with Air	40
SPARK PLUG	41
Fig. 38 Gapping the Spark Plug	41
Cleaning the Battery	41
Fig. 39 Preparing Acid Neutralizing Solution	41
Battery Removal and Installation	41
Fig. 40 Battery Removal	42
.	42
Periodic Brake Performance Test (PBPT)	42
Fig. 41 Periodic Brake Performance Test	43
Over time, a subtle loss of performance may take place; therefore, it is important to establish the standard with a new vehicle.	43
PROLONGED STORAGE	43
F Specification--gas-10Feb10.pdf	48
RXV GAS - FREEDOM VEHICLE SPECIFICATIONS	49
RXV GAS - SHUTTLE 2 + 2 VEHICLE SPECIFICATIONS	50
Fig. 42 Flee & Freedom Vehicle Dimensions	51
Fig. 42 Shuttle 2 + 2 Vehicle Dimensions	52

Match case Limit results 1 per page

Page 10

OPERATION AND SERVICE INFORMATION

Owner’s Guide

Read all of manual to become familiar with this vehicle. Pay attention to all NOTICES, CAUTIONS, WARNINGS and DANGERS.

Tire plug tools and plugs are available at most automotive

parts outlets and have the advantage of not requiring the tire

be removed from the wheel.

If the tire is flat, remove the wheel and inflate the tire to

the maximum recommended pressure for the tire.

Immerse the tire in water to locate the leak and mark

with chalk. Insert tire plug in accordance with manufac-

turer’s instructions

To reduce the possibility of severe injury, be

sure the mounting/demounting machine is

anchored to floor. Wear OSHA approved safe-

ty equipment when mounting/demounting tires.

If the tire is to be removed or mounted, the tire changing

machine manufacturer’s recommendations must be fol-

lowed in order to reduce possibility of severe injury.

WHEEL INSTALLATION

To reduce the possibility of component damage, do not

tighten lug nuts to more than 85 ft. lbs. (115 Nm)

torque.

It is important to follow the ‘cross sequence’ pattern when

installing lug nuts. This will assure even seating of the wheel

against the hub.

With the valve stem to the outside, mount the wheel on-

to the hub with lug nuts. Finger tighten the lug nuts in a

‘cross sequence’ pattern (Ref. Fig. 14). Tighten the lug

nuts to 50 - 85 ft. lbs. (70 - 115 Nm) torque in 20 ft. lbs.

(30 Nm) increments following the ‘cross sequence’ pat-

tern.(Ref. Fig. 14)

Fig. 14

Wheel Installation

Light Bulb Replacement

To reduce the possibility of premature bulb failure, do

not touch new bulbs with bare fingers. Use clean, dry

tissue or paper towel to handle the glass portion of the

bulb.

HEAD LIGHT BULB REPLACEMENT

Make sure that the vehicle key switch is in the ’OFF’ po-

sition and the key has been removed. For vehicles

equipped with lights mounted in the cowl, locate the

headlight bulb socket on the backside of the light as-

sembly.

Turn the headlight bulb (3) clockwise and pull to

remove.

Disconnect the accessory harness (5) from the light

bulb.

NOTICE

Valve Stem Cap

Cross Sequence

Tire style may vary