Electrolux E42BS75ETT Owners Manual - Page 31

Connect, Power, Level Refrigerator

Page 31 highlights

Installation Instructions [] CONNECT POWER • Connect refrigerator power cord plug to a properly grounded receptacle. Set the Master Power switch to the I (ON} position. I o o o _Raise t _Orille,,_ _Panel _ • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. CAUTION: • After power has been established, turn the Master Power switch to the O (OFF) position. [] MOVE INTO INSTALLATION SPACE • Slide the unit into the installation space. • Place excess slack in the power cord on top of the refrigerator. • Use care to ensure the power cord is not pinched behind the unit. Height tr0m Floor to Bottom or Wood Block 82" [] LEVEL REFRIGERATOR All models have 4-point leveling. The front and back are supported by leveling legs. Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 1/2" hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator. • For front leveling, use a 7/16" open-end wrench. Adjust height of refrigerator to match installation cutout opening 83-1/2" to 84-1/2". The refrigerator should be level and plumb with cabinets. l[ I LevelinLgeg__ IMPORTANT NOTE: The refrigerator must be level. If it is not, the doors may not align evenly at the top. See Step 16. CAUTION: The rear leveling legs and front leveling legs are limited to a maximum height adjustment of 1". If the installation requires more than 84-1/2" height, the installer should elevate the refrigerator on a sheet of plywood or runners. Cabinet trim could be added across the top of the opening to shorten the opening. If you attempt to raise the refrigerator more than 1", you will damage the front and rear leveling legs. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

Installation
Instructions
[]
CONNECT
POWER
Connect
refrigerator
power
cord
plug
to
a properly
grounded
receptacle.
Set the
Master
Power
switch
to
the I (ON}
position.
I
o
o
_Raise
t
_Orille,,_
_Panel
_
o
Check
to
make
sure
power
to
refrigerator
is on
by
opening
refrigerator
door
to see if
interior
lights
are on.
CAUTION:
After power
has been
established,
turn the
Master
Power
switch
to the
O (OFF)
position.
[]
MOVE
INTO
INSTALLATION
SPACE
Slide
the unit
into
the
installation
space.
Place
excess
slack
in the
power
cord
on top
of the
refrigerator.
Use
care
to ensure
the
power
cord
is not
pinched
behind
the
unit.
Height
tr0m
Floor to
Bottom
or Wood
Block
82"
[]
LEVEL REFRIGERATOR
All
models
have
4-point
leveling.
The
front
and
back are
supported
by
leveling
legs.
Both
are
accessible
from
the front
of the refrigerator.
To level
the
back
of the
refrigerator,
turn
the
1/2"
hex
nut
located
above
the front
wheels.
Turn
clockwise
to
raise
or
counterclockwise
to
lower
the
refrigerator.
For front
leveling,
use a 7/16"
open-end
wrench.
Adjust
height
of
refrigerator
to
match
installation
cutout
opening
83-1/2"
to
84-1/2".
The
refrigerator
should
be level
and
plumb
with
cabinets.
l[
I
Leveling
Leg__
IMPORTANT
NOTE:
The
refrigerator
must
be level.
If it is not,
the doors
may
not align
evenly
at the top.
See
Step
16.
CAUTION:
The
rear
leveling
legs
and
front
leveling
legs
are
limited
to
a maximum
height
adjustment
of
1". If the
installation
requires
more
than
84-1/2"
height,
the
installer
should
elevate
the
refrigerator
on a sheet
of
plywood
or
runners.
Cabinet
trim
could
be added
across
the
top
of
the opening
to
shorten
the
opening.
If
you
attempt
to raise
the
refrigerator
more
than
1", you
will
damage
the
front
and
rear
leveling
legs.
31