Epson 830p User Manual - Page 80

Connecting and Configuring the Projector on a Wired Network

Get Epson 830p - PowerLite XGA LCD Projector PDF manuals and user guides
UPC - 010343851177
View all Epson 830p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

note If you're a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the projectors you're monitoring. Connecting and Configuring the Projector on a Wired Network Before using the EasyManagement software to manage your projector(s), you have to connect each projector you want to monitor to your network and configure it with an appropriate IP address. You can connect and configure the projector using the network port. Follow these steps to connect and configure the projector for your network. 1. Connect the projector to your network using a commercially available 100baseTX or 10baseT network cable. 2. Turn on the projector (see page 18). 3. Press the Menu button on the remote control and select Network from the Extended menu. 4. If your network assigns addresses automatically, turn on DHCP. If your network does not assign addresses automatically, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. ■ To enter numbers using the remote control, press the Num button until it lights, then use the number keypad shown below. 80 Managing Projectors

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
80
Managing Projectors
Connecting and Configuring the
Projector on a Wired Network
Before using the EasyManagement software to manage your
projector(s), you have to connect each projector you want to monitor
to your network and configure it with an appropriate IP address. You
can connect and configure the projector using the network port.
Follow these steps to connect and configure the projector for your
network.
1.
Connect the projector to your network using a commercially
available 100baseTX or 10baseT network cable.
2.
Turn on the projector (see page 18).
3.
Press the
Menu
button on the remote control and select
Network
from the
Extended
menu.
4.
If your network assigns addresses automatically, turn on
DHCP
.
If your network does not assign addresses automatically, turn off
DHCP
and enter the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
, as needed.
■
To enter numbers using the remote control, press the
Num
button until it lights, then use the number keypad shown
below.
note
If you’re a network
administrator, you can use
the
SNMP
option to enter a
trap IP address. This lets you
receive trap alerts for the
projectors you’re monitoring.