Epson 830p User Manual - Page 81

Using EMP Monitor

Get Epson 830p - PowerLite XGA LCD Projector PDF manuals and user guides
UPC - 010343851177
View all Epson 830p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

■ To change the network addresses from the projector's control panel, press the right and left arrow buttons to select the part of the address you want to enter, then use the up and down arrow buttons to increase or decrease the numeric value. Increase or decrease the value Select the part of the address to change When you finish changing an address in the network menu, press the Enter button (on the remote control) or the Auto/Enter button (on the projector). 5. When you're done, press Esc to exit the menu system. Using EMP Monitor EMP Monitor lets you use a remote computer to manage your projectors over a wired network. It lets you easily turn the projectors on or off (together or individually), switch image sources, and check their status. Before using EMP Monitor, make sure you've installed the software (available for Windows only) as described on page 114. The computer you're using to monitor the projector should already be connected to your network. note If you want to monitor projectors while they are in standby mode, select Standby Mode in the Extended menu, then select Network ON. See page 75. Managing Projectors 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Managing Projectors
81
■
To change the network addresses from the projector’s control
panel, press the right and left arrow buttons to select the part
of the address you want to enter, then use the up and down
arrow buttons to increase or decrease the numeric value.
When you finish changing an address in the network menu, press
the
Enter
button (on the remote control) or the
Auto/Enter
button (on the projector).
5.
When you’re done, press
Esc
to exit the menu system.
Using EMP Monitor
EMP Monitor lets you use a remote computer to manage your
projectors over a wired network. It lets you easily turn the projectors
on or off (together or individually), switch image sources, and check
their status.
Before using EMP Monitor, make sure you’ve installed the software
(available for Windows only) as described on page 114. The
computer you’re using to monitor the projector should already
be connected to your network.
Increase
or
decrease
the value
Select the part of the
address to change
note
If you want to monitor
projectors while they are in
standby mode, select
Standby Mode
in the
Extended menu, then select
Network ON
. See page 75.