Epson LW-600P Quick Start and Warranty - Page 28

Industry Canada IC Notices, Contains IC: 337L-MBH7BTZXXC2

Get Epson LW-600P PDF manuals and user guides View all Epson LW-600P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ■ Reorient or relocate the receiving antenna. ■ Increase the separation between the equipment and receiver. ■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ■ Consult the dealer or an experienced radio/TV technician for help. An AC adaptor with a ferrite core must be used for RF interference suppression. Warning: The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than 26 | Notices one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 7.8 inches (20 cm) between the radiator and your body. Industry Canada (IC) Notices Contains IC: 337L-MBH7BTZXXC2 This Class B digital apparatus complies with Canadian ICES-003. This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
26
|
Notices
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of
the following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment
and receiver.
■
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
■
Consult the dealer or an experienced radio/TV
technician for help.
An AC adaptor with a ferrite core must be used for RF
interference suppression.
Warning: The connection of a non-shielded
equipment interface cable to this equipment will
invalidate the FCC Certification or Declaration of
this device and may cause interference levels which
exceed the limits established by the FCC for this
equipment. It is the responsibility of the user to
obtain and use a shielded equipment interface cable
with this device. If this equipment has more than
one interface connector, do not leave cables
connected to unused interfaces. Changes or
modifications not expressly approved by the party
responsible for compliance could void the user’s
authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 7.8 inches (20 cm) between the
radiator and your body.
Industry Canada (IC) Notices
Contains IC: 337L-MBH7BTZXXC2
This Class B digital apparatus complies with Canadian
ICES-003.
This device complies with RSS-210 of the Industry
Canada Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.