Epson Perfection 600 Quick Start - Page 12

cord, and where the SCSI cable can reach your computer.

Get Epson Perfection 600 PDF manuals and user guides View all Epson Perfection 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CHOOSE A GOOD PLACE FOR YOUR SCANNER Here are some points to consider:  Place the scanner on a flat, stable surface. If the scanner is tilted, it can't operate properly.  Make sure to place the scanner where you can easily unplug the power cord, and where the SCSI cable can reach your computer.  Be sure there's enough room behind the scanner for the cables, and above the scanner so you can fully raise the document cover, if necessary.  Keep the scanner away from direct sunlight and strong light sources.  Avoid places subject to shocks and vibrations, or high temperatures and humidity. INSTALL THE SCSI INTERFACE BOARD (PC ONLY) You must install your SCSI board and SCSI software before installing the scanner driver and software applications. If you have a Macintosh or if you already have a SCSI board installed in your PC, skip this section. Note: For additional information, see the Installation Guide that came with your SCSI board. 1. Turn off the computer and any peripheral devices. Unplug any power cords; then disconnect all cables from the back panel of your computer. 2. Remove the cover from your computer. Caution: Ground yourself before you touch any of the computer's internal components by touching an unpainted metal surface inside the computer case. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
8
I
NSTALL
T
HE
SCSI I
NTERFACE
B
OARD
(PC O
NLY
)
You must install your SCSI board and SCSI software before installing the
scanner driver and software applications.
If you have a Macintosh or if you already have a SCSI board installed in
your PC, skip this section.
Note
:
For additional information, see the Installation Guide that came with your
SCSI board.
1.
Turn off the computer and any peripheral devices. Unplug any power
cords; then disconnect all cables from the back panel of your computer.
2.
Remove the cover from your computer.
Caution
:
Ground yourself before you touch any of the computer’s internal components
by touching an unpainted metal surface inside the computer case.
C
HOOSE
A G
OOD
P
LACE
F
OR
Y
OUR
S
CANNER
Here are some points to consider:
Place the scanner on a flat, stable surface. If the scanner is tilted, it can’t
operate properly.
Make sure to place the scanner where you can easily unplug the power
cord, and where the SCSI cable can reach your computer.
Be sure there’s enough room behind the scanner for the cables, and above
the scanner so you can fully raise the document cover, if necessary.
Keep the scanner away from direct sunlight and strong light sources.
Avoid places subject to shocks and vibrations, or high temperatures and
humidity.