Esoteric Grandioso D1 Owners Manual EN FR SP - Page 19

Troubleshooting, A beeping noise is output at a regular interval.

Get Esoteric Grandioso D1 PDF manuals and user guides View all Esoteric Grandioso D1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

English Troubleshooting If you experience a problem with this unit, please take a moment to review the following information before requesting service. The problem could also be something other than this unit. Please also check the operation of the connected units. If this unit still does not operate correctly, contact the retailer where you purchased the unit. This unit uses a microprocessor, so noise and other external interference could cause it to stop functioning properly. In such a case, turn the unit off and wait about one minute before restarting operation from the beginning. The unit does not turn on. eeConfirm that the power cord is securely connected to both the inlet on the back of this unit and a power outlet. eeConfirm that power is being supplied to the outlet to which the power cord is connected by, for example, connecting another device to it. eeCheck if the power source is a switched outlet. If it is, make sure it is turned on. The unit automatically turns off. eeThis is because the automatic power saving function turned it off. Turn the unit on again. Change the automatic power saving function time if necessary (page 16). No sound is output from the speaker. The sound is distorted. eeIn this case, turn the power off and check the connections with the digital audio source device, the amp and the speaker (page 8). eeChange the input setting to the connector that is being used for input (page 12). eeSet AOUT (analog output) according to the amp connection. eeAdjust the volume of the amp, for example. No sampling frequency is shown to the right of "INPUT" on the display. eeTurn the device that is connected to the selected input connector on. eeConfirm that the device is properly connected to the selected input connector. A beeping noise is output at a regular interval. eeIf a beeping noise is output at a regular interval when the unit is in clock sync mode, the connected device might not also be in clock sync mode. Check the connections of the clock input connectors and the clock sync setting of the connected device. The CLOCK indicator does not stop blinking. eeSet CLK> to OFF when not using clock sync (page 14). eeA clock signal with which the unit cannot be synchronized might be being input. Check the connections of the clock input connectors and the settings of the connected device. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
19
19
English
Troubleshooting
If you experience a problem with this unit, please take a moment to
review the following information before requesting service. The prob-
lem could also be something other than this unit. Please also check
the operation of the connected units.
If this unit still does not operate correctly, contact the retailer where
you purchased the unit.
The unit does not turn on.
e
Confirm that the power cord is securely connected to both the
inlet on the back of this unit and a power outlet.
e
Confirm that power is being supplied to the outlet to which the
power cord is connected by, for example, connecting another
device to it.
e
Check if the power source is a switched outlet. If it is, make sure
it is turned on.
The unit automatically turns off.
e
This is because the automatic power saving function turned it
off. Turn the unit on again. Change the automatic power saving
function time if necessary (page 16).
No sound is output from the speaker. The sound is distorted.
e
In this case, turn the power off and check the connections with
the digital audio source device, the amp and the speaker (page
8).
e
Change the input setting to the connector that is being used for
input (page 12).
e
Set AOUT (analog output) according to the amp connection.
e
Adjust the volume of the amp, for example.
No sampling frequency is shown to the right of “INPUT” on the
display.
e
Turn the device that is connected to the selected input connec-
tor on.
e
Confirm that the device is properly connected to the selected
input connector.
A beeping noise is output at a regular interval.
e
If a beeping noise is output at a regular interval when the unit is
in clock sync mode, the connected device might not also be in
clock sync mode. Check the connections of the clock input con-
nectors and the clock sync setting of the connected device.
The CLOCK indicator does not stop blinking.
e
Set CLK> to OFF when not using clock sync (
page 14).
e
A clock signal with which the unit cannot be synchronized
might be being input. Check the connections of the clock input
connectors and the settings of the connected device.
This unit uses a microprocessor, so noise and other exter-
nal interference could cause it to stop functioning properly.
In such a case, turn the unit off and wait about one minute
before restarting operation from the beginning.