Esoteric Grandioso D1 Owners Manual EN FR SP - Page 20

Messages, Restoring factory settings

Get Esoteric Grandioso D1 PDF manuals and user guides View all Esoteric Grandioso D1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Troubleshooting (continued) Restoring factory settings Messages - - - appears in the sampling frequency display area. There is a problem with the input signal. Do not input signals other than PCM or DSD. Check the connection with the digital device. This unit cannot decode signals in formats such as Dolby Digital, DTS and AAC. Have the playback device convert the signal to PCM before output. Settings are retained even if the power plug is disconnected. Follow these procedures to restore all settings to their factory defaults and clear the unit's memory. 1 Turn the unit off. If the power is on, press the POWER button and wait at least 30 seconds before proceeding. No sampling frequency is shown to the right of "INPUT" on the display. The digital signal cannot be locked. Press the INPUT selection button and select the connector to which the digital device is connected. Turn the connected device on. Check the settings of the connected device. CLOCK! 2 Press the POWER button while pressing and holding the MENU button. When "Setup CLR" (clear settings) appears on the display, release the MENU button. Check settings related to the clock. If there is no input clock, "- - -" will appear in the clock frequency display area. If the set mode and the input clock are incorrect, the clock frequency display area will blink. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
20
20
Messages
– – –
appears in the sampling frequency display area.
There is a problem with the input signal.
Do not input signals other than PCM or DSD.
Check the connection with the digital device.
This unit cannot decode signals in formats such as Dolby Digital, DTS
and AAC. Have the playback device convert the signal to PCM before
output.
No sampling frequency is shown to the right of “INPUT” on the
display.
The digital signal cannot be locked. Press the INPUT selection button
and select the connector to which the digital device is connected.
Turn the connected device on. Check the settings of the connected
device.
CLOCK!
Check settings related to the clock.
If there is no input clock, “– – –” will appear in the clock frequency
display area.
If the set mode and the input clock are incorrect, the clock frequency
display area will blink.
Restoring factory settings
Settings are retained even if the power plug is disconnected.
Follow these procedures to restore all settings to their factory
defaults and clear the unit’s memory.
1
Turn the unit off.
If the power is on, press the POWER button and wait at least 30
seconds before proceeding.
2
Press the POWER button while pressing and holding
the MENU button.
When “Setup CLR” (clear settings) appears on the display, release
the MENU button.
Troubleshooting (continued)