Fisher and Paykel OR36SCG6R1 Installation Guide - Page 24

Adjusting the cooktop burner minimums

Get Fisher and Paykel OR36SCG6R1 PDF manuals and user guides View all Fisher and Paykel OR36SCG6R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

GAS CONVERSION Adjusting the cooktop burner minimums When switching from one type of gas to another, the minimum flow rate must also be correct: z The flame should not go out even when passing suddenly from maximum to minimum flame. To regulate the flame follow these instructions: Semi-rapid burner (A) z Light the burner z Set the gas valve to position (minimum rate) z Remove the dial. z With a thin screwdriver, turn the regulation screw inside the tap rod until adjustment is correct. Inside crown of DUAL burner (B) z Light the dual burner z Set the gas valve to position (minimum rate of inner crown) z Remove the dial z With a thin screwdriver, turn the regulation screw until adjustment is correct. z The screw is accessible via a hole in the microswitch. Outside crown of DUAL burner (C) z Light the dual burner z Set the gas valve to position (minimum rate of outer crown and maximum rate of inner crown). z Remove the dial z With a thin screwdriver, turn the regulation screw inside the tap rod until adjustment is correct. For LP/PROPANE gas, tighten the adjustmentacrews completely. A Regulation screw (triple ring and semi-rapid burner) B Regulation screw (inner crown of dual burner) C Regulation screw (outer crown of dual burner) Regulation screws A Regulation screws C B Regulation screws 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
24
Adjusting the cooktop burner minimums
When switching from one type of gas to another, the minimum flow rate
must also be correct:
The flame should not go out even when passing suddenly from
maximum to minimum flame.
To regulate the flame follow these instructions:
Semi-rapid burner (
A
)
Light the burner
Set the gas valve to
position (minimum rate)
Remove the dial.
With a thin screwdriver, turn the regulation screw inside the tap rod
until adjustment is correct.
Inside crown of DUAL burner (
B
)
Light the dual burner
Set the gas valve to
position (minimum rate of inner crown)
Remove the dial
With a thin screwdriver, turn the regulation screw until adjustment is correct.
The screw is accessible via a hole in the microswitch.
Outside crown of DUAL burner (
C
)
Light the dual burner
Set the gas valve to
position
(minimum rate of outer crown and maximum rate of inner crown).
Remove the dial
With a thin screwdriver, turn the regulation screw inside the tap rod
until adjustment is correct.
For LP/PROPANE gas, tighten the adjustmentacrews completely.
A
Regulation screw (triple ring and semi-rapid burner)
B
Regulation screw (inner crown of dual burner)
C
Regulation screw (outer crown of dual burner)
GAS CONVERSION
Regulation
screws
A
Regulation
screws
C
B
Regulation
screws