Fujitsu MAN3735MC Manual/User Guide - Page 127

frame configuration., Training area

Get Fujitsu MAN3735MC - Enterprise 73.5 GB Hard Drive PDF manuals and user guides View all Fujitsu MAN3735MC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

1) Dead space The dead space is at the innermost position of a disk. At spindle start and stop, the head is in contact with this area of the disk. 2) Inner guard band (IGB) IGB is located in an inner position of a disk. IGB is used to detect that actuator operation has exceeded the ordinary seek operation range. 3) Data zone The servo zone is the data recording part on the data side. Ordinary head seek operations are done within this zone. 4) Outer guard band (OGB) OGB is located in an outer position of a disk. Like IGB, OGB is also used to detect that actuator operation has exceeded the ordinary seek operation range. (2) Frame format The servo pattern consists of 120 servo frames for MAN series per one revolution. One servo frame is divided into 4 areas and these areas are separated with a gap. Figure 8.6 shows the servo frame configuration. 1) Training area The training area consists of a fixed-period burst signal and has following functions. • Preparation of servo mark detection • Gap 2) Servo mark area Servo mark patterns are written in the servo mark areas and patterns are detected by the length of the DC areas. The servo mark determines the starting point for detecting a position pattern and gray code pattern. 3) Gap area The gap area is located before and after the gray code area and position area. The gap area prevents the misdetection of the gray code pattern or position pattern by releasing a synchronization of the servo mark or delaying a reference counter. C141-E128-01EN 8 - 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
C141-E128-01EN
8 - 11
1)
Dead space
The dead space is at the innermost position of a disk.
At spindle start and stop, the head is in
contact with this area of the disk.
2)
Inner guard band (IGB)
IGB is located in an inner position of a disk.
IGB is used to detect that actuator operation has
exceeded the ordinary seek operation range.
3)
Data zone
The servo zone is the data recording part on the data side.
Ordinary head seek operations are
done within this zone.
4)
Outer guard band (OGB)
OGB is located in an outer position of a disk.
Like IGB, OGB is also used to detect that
actuator operation has exceeded the ordinary seek operation range.
(2)
Frame format
The servo pattern consists of 120 servo frames for MAN series per one revolution.
One servo
frame is divided into 4 areas and these areas are separated with a gap.
Figure 8.6 shows the servo
frame configuration.
1)
Training area
The training area consists of a fixed-period burst signal and has following functions.
•
Preparation of servo mark detection
•
Gap
2)
Servo mark area
Servo mark patterns are written in the servo mark areas and patterns are detected by the length
of the DC areas.
The servo mark determines the starting point for detecting a position pattern
and gray code pattern.
3)
Gap area
The gap area is located before and after the gray code area and position area.
The gap area
prevents the misdetection of the gray code pattern or position pattern by releasing a
synchronization of the servo mark or delaying a reference counter.