Gateway E-9425R Gateway E-9425R Server User Guide - Page 64

Resetting the BIOS

Get Gateway E-9425R PDF manuals and user guides View all Gateway E-9425R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

CHAPTER 5: Using the BIOS Setup Utility 12 Follow the instructions in "Closing the server case" on page 30. 13 Plug in the AC power cords and turn on the server, then verify that the recovery was successful. Resetting the BIOS You can use two methods to clear all BIOS Setup settings and return them to the factory defaults: • Press the power and reset buttons on the front of the server. • Move the Clear CMOS jumper on the system board. To reset the BIOS using the power and reset buttons: 1 Print the appendix for "BIOS Settings" on page 89 in this guide. 2 Restart your server, then press F2 at any time after you see the LEDs on your keyboard flash or turn off. The BIOS Setup utility opens. 3 Record any custom BIOS settings on your printout. 4 Press the reset button and hold it down for four seconds or more, then press the power button while continuing to hold down the reset button. 5 Release both buttons at the same time. The BIOS is reset. To reset the BIOS using the system board jumper: 1 Print the appendix for "BIOS Settings" on page 89 in this guide. 2 Restart your server, then press F2 at any time after you see the LEDs on your keyboard flash or turn off. The BIOS Setup utility opens. 3 Record any custom BIOS settings on your printout. 4 Follow the instructions in "Preventing static electricity discharge" on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 5 Follow the instructions in "Opening the server case" on page 29. 6 Remove the jumper across pins 1-2 of header J3-B, then place the jumper across pins 2-3. Caution Moving the jumper while the power is on can damage your server. Always turn off the server and unplug the power cords and all other cables before changing the jumper. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
CHAPTER 5: Using the BIOS Setup Utility
58
12
Follow the instructions in
“Closing the server case” on page 30
.
13
Plug in the AC power cords and turn on the server, then verify that the recovery was
successful.
Resetting the BIOS
You can use two methods to clear all BIOS Setup settings and return them to the factory defaults:
•
Press the power and reset buttons on the front of the server.
•
Move the Clear CMOS jumper on the system board.
To reset the BIOS using the power and reset buttons:
1
Print the appendix for
“BIOS Settings” on page 89
in this guide.
2
Restart your server, then press F2 at any time after you see the LEDs on your keyboard
flash or turn off. The BIOS Setup utility opens.
3
Record any custom BIOS settings on your printout.
4
Press the reset button and hold it down for four seconds or more, then press the power
button while continuing to hold down the reset button.
5
Release both buttons at the same time. The BIOS is reset.
To reset the BIOS using the system board jumper:
1
Print the appendix for
“BIOS Settings” on page 89
in this guide.
2
Restart your server, then press F2 at any time after you see the LEDs on your keyboard
flash or turn off. The BIOS Setup utility opens.
3
Record any custom BIOS settings on your printout.
4
Follow the instructions in
“Preventing static electricity discharge” on page 28
. Make sure that
you turn off the server, then unplug the power cord(s) and all other cables connected to the
server.
5
Follow the instructions in
“Opening the server case” on page 29
.
6
Remove the jumper across pins 1-2 of header J3-B, then place the jumper across pins 2-3.
Caution
Moving the jumper while the power is on can damage your server. Always
turn off the server and unplug the power cords and all other cables before changing
the jumper.