Gateway E-9722R Gateway E-9722R Server User Guide - Page 20

Turning off your server, Setting up the operating system, Initial hardware settings

Get Gateway E-9722R PDF manuals and user guides View all Gateway E-9722R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

CHAPTER 2: Setting Up Your Server Turning off your server Every time you turn off your server, first shut down the operating system. You may lose data if you do not follow the correct procedure. To turn off the server: Caution The power button on the server does not turn off server AC power. To remove AC power from the server, you must unplug the AC power cords from the wall outlet or power source. The power cords are considered the disconnect device to the main (AC) power. 1 Use the instructions in the operating system's documentation or online help to shut down the operating system. Whenever possible, you should use the operating system's shut down procedure instead of pressing the power button. 2 If your server did not turn off automatically, press the power button. - OR Press the reset button to reset the server. Setting up the operating system If you ordered your server with the operating system already installed by Gateway, in most cases it is completely installed and the basic settings are already configured. The Windows Small Business Server operating system may require additional installation, depending on the version you ordered. See your operating system's documentation for instructions on completing the installation or configuring advanced settings for your specific network. If you are installing an operating system because it was not already installed by Gateway, see the appropriate installation guide for instructions. Initial hardware settings Your server comes from the manufacturer with the correct initial hardware settings to operate your server as configured. However, at some point you might want to change settings to reflect a tasking change, a change in security requirements, or the addition of new resources to your server. You can change general hardware settings by using the BIOS Setup utility. For information on the BIOS Setup utility, see "Using the BIOS Setup Utility" on page 51. For information on BIOS settings, see "BIOS Settings" on page 83. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
CHAPTER 2: Setting Up Your Server
14
Turning off your server
Every time you turn off your server, first shut down the operating system. You may lose data if
you do not follow the correct procedure.
To turn off the server:
1
Use the instructions in the operating system’s documentation or online help to shut down
the operating system. Whenever possible, you should use the operating system’s shut down
procedure instead of pressing the power button.
2
If your server did not turn off automatically, press the power button.
- OR -
Press the reset button to reset the server.
Setting up the operating system
If you ordered your server with the operating system already installed by Gateway, in most cases
it is completely installed and the basic settings are already configured. The Windows Small
Business Server operating system may require additional installation, depending on the version
you ordered. See your operating system’s documentation for instructions on completing the
installation or configuring advanced settings for your specific network.
If you are installing an operating system because it was not already installed by Gateway, see
the appropriate installation guide for instructions.
Initial hardware settings
Your server comes from the manufacturer with the correct initial hardware settings to operate
your server as configured. However, at some point you might want to change settings to reflect
a tasking change, a change in security requirements, or the addition of new resources to your
server.
You can change general hardware settings by using the BIOS Setup utility. For information on
the BIOS Setup utility, see
“Using the BIOS Setup Utility” on page 51
. For information on BIOS
settings, see
“BIOS Settings” on page 83
.
Caution
The power button on the server does not turn off server AC power. To
remove AC power from the server, you must unplug the AC power cords from the
wall outlet or power source. The power cords are considered the disconnect device
to the main (AC) power.