Gateway E-9722R Gateway E-9722R Server User Guide - Page 43

Position the PCI riser card assembly 1 over the PCI socket on the server board, then press

Get Gateway E-9722R PDF manuals and user guides View all Gateway E-9722R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

www.gateway.com 9 Press the tab (8) holding the riser card in the riser card assembly, then push the riser card in the direction shown (9) to unlock and remove it from the standoffs. Standoff 10 Insert the new riser card into the riser card assembly, then push it toward the back of the assembly. It should snap into place. 11 Insert the new PCI card into the riser card, making sure any connectors extend through the slot at the back of the assembly and that the card is fully seated in the riser card. 12 Close the release lever (see Step 6) and the card guide tab. 13 Position the PCI riser card assembly (1) over the PCI socket on the server board, then press the PCI riser card assembly into the PCI socket until it clicks into place. 14 Follow the instructions in "Closing the server case" on page 27. 15 See the card's documentation for software installation instructions. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
www.gateway.com
37
9
Press the tab (8) holding the riser card in the riser card assembly, then push the riser card
in the direction shown (9) to unlock and remove it from the standoffs.
10
Insert the new riser card into the riser card assembly, then push it toward the back of the
assembly. It should snap into place.
11
Insert the new PCI card into the riser card, making sure any connectors extend through the
slot at the back of the assembly and that the card is fully seated in the riser card.
12
Close the release lever (see
Step 6
) and the card guide tab.
13
Position the PCI riser card assembly (1) over the PCI socket on the server board, then press
the PCI riser card assembly into the PCI socket until it clicks into place.
14
Follow the instructions in
“Closing the server case” on page 27
.
15
See the card’s documentation for software installation instructions.
Standoff