Gateway FX530XV 8511781 - FX Reference Guide - Page 51

Setting up multiple monitors - desktops

Page 51 highlights

CHAPTER 4: Advanced Hardware Setup www.gateway.com 9 Press the - (minus) or +(plus) key repeatedly to adjust the multiplier, then press Enter. 10 Press F10 to exit BIOS, then press Y to accept the changes. The screen displays the message "Turn off power and reinstall the jumper in Normal mode position." 11 Turn off the computer. 12 Disconnect the power cord and follow all anti-static precautions. 13 Return the jumper to the Normal position (bridging pins 1-2). 14 Reconnect the power cord. 15 Turn the computer on. If the jumper is in the correct position and the multiplier is low enough, your computer should start normally. Setting up multiple monitors Using a projector or second monitor Important The dialog boxes shown in this section are for demonstrative purposes only and may not represent the screens on your computer. If your computer's video card supports additional monitors (it must have two video connections), you can connect an additional monitor or projector to your computer. You can use the second monitor or projector as a duplicate of the primary display, or as an extension to roughly double the size of your Windows desktop. Use the additional desktop space to accommodate additional windows. To use a projector or additional monitor: 1 Turn off your computer. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143

CHAPTER 4: Advanced Hardware Setup
46
www.gateway.com
9
Press the - (minus) or +(plus) key
repeatedly to adjust the multiplier, then
press
Enter
.
10
Press
F10
to exit BIOS, then press
Y
to
accept the changes. The screen displays
the message “Turn off power and reinstall
the jumper in Normal mode position.”
11
Turn off the computer.
12
Disconnect the power cord and follow all
anti-static precautions.
13
Return the jumper to the Normal position
(bridging pins 1-2).
14
Reconnect the power cord.
15
Turn the computer on. If the jumper is in
the correct position and the multiplier is
low enough, your computer should start
normally.
Setting up multiple monitors
Using a projector or second monitor
Important
The dialog boxes
shown in this section
are for demonstrative
purposes only and
may not represent the
screens on your
computer.
If your computer’s video card supports
additional monitors (it must have two video
connections), you can connect an additional
monitor or projector to your computer.
You can use the second monitor or projector as
a duplicate of the primary display, or as an
extension to roughly double the size of your
Windows desktop. Use the additional desktop
space to accommodate additional windows.
To use a projector or additional monitor:
1
Turn off your computer.