GE AEM08LP Owners Manual - Page 8

Iti IAir Conditio

Get GE AEM08LP PDF manuals and user guides View all GE AEM08LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

I ti Air Conditio I structi as !r_ Questions? Call 800.GE.CARES {800.432.2737) or Visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca r 1 BEFORE YOU BEGIN CAUTION: Do not, under any circumstances, cut or remove Read these instructions completely the third {ground) prong from the power cord. and carefully. Do not change the plug on the power cord of this air conditioner. • IMPORTANT - Savtehesienstructions Aluminum house wiring may present special for local inspector's use. problems--consult a qualified electrician. • IMPORTANT - Observe all governing codes and ordinances. • Note to Installer- Be sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions for future reference. TOOLS YOU WILL NEED • Skill level - Installation of this appliance requires basic mechanical skills. • Completion time - Approximately 1 hour . We recommend that two people install this product. . Proper installation is the responsibility of the installer. Phillips head screwdriver Product failure due to improper installation is not covered under the Warranty. You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner. Flat-blade screwdriver ELECTRICAL REQUIREMENTS S60o-mHez mgrooduenldsedreqouuirteleta p1ro1t5e/c1t2e0d-vowltithAaC, 15-amp time-delay fuse or circuit breaker. The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet. Some models require 230/208-volt AC, protected with a time-delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires. Pencil Ruler or tape measure Level Scissorsor knife Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESETbutton while plugged into the outlet. If the TEST button does not trip or if the RESETbutton will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
!
I
I
ti
structi
as
Air Conditio
r_
Questions?
Call 800.GE.CARES {800.432.2737)
or Visit our Website
at: GEAppliances.com
In Canada,
call
1.800.561.3344
or visit
www.GEAppliances.ca
r
1
BEFORE YOU BEGIN
Read these
instructions
completely
and
carefully.
•IMPORTANT
-
Save
these
instructions
for local
inspector's
use.
•
IMPORTANT
-
Observe
all governing
codes and ordinances.
•
Note to Installer-
Be sure to leave these
instructions
with the Consumer.
•
Note to Consumer
- Keep these
instructions
for
future
reference.
•
Skill level
- Installation
of this appliance
requires
basic mechanical
skills.
•
Completion
time
- Approximately
1 hour
.
We recommend
that
two
people
install this
product.
.
Proper installation
is the responsibility
of the
installer.
Product
failure
due to improper
installation
is not
covered
under
the Warranty.
You MUST use all supplied
parts
and use proper
installation
procedures
as described
in these
instructions
when
installing
this air conditioner.
ELECTRICAL
REQUIREMENTS
Some models require a 115/120-volt
AC,
60-Hz grounded
outlet protected
with a
15-amp time-delay
fuse or circuit
breaker.
The 3-prong
grounding
plug minimizes the
possibility of electric shock hazard. If the wall outlet
you plan to use is only a 2-prong
outlet, it is your
responsibility
to have it replaced with a properly
grounded
3-prong
wall outlet.
Some models require 230/208-volt
AC,
protected with a time-delay
fuse or circuit
breaker. These models should be installed
on their own single branch circuit for best
performance
and to prevent overloading
house or apartment
wiring circuits, which
could cause a possible fire hazard from
overheating
wires.
CAUTION:
Do not,
under
any circumstances,
cut or remove
the third
{ground)
prong
from
the power
cord.
Do not change
the
plug on the power
cord
of this
air conditioner.
Aluminum
house
wiring
may present
special
problems--consult
a qualified
electrician.
TOOLS YOU WILL
NEED
Phillips head screwdriver
Flat-blade screwdriver
Pencil
Ruler or tape measure
Level
Scissorsor knife
Power cord includes a current interrupter
device. A test and reset button is provided on the
plug case. The device should be tested on a periodic
basis by first pressing the TEST button
and then the
RESETbutton while plugged
into the outlet. If the
TESTbutton does not trip or
if the RESETbutton will not stay engaged, discontinue
use of the air conditioner
and contact
a qualified
service technician.