Hamilton Beach HBS1200 Operation Manual - Page 12

Cleaning Instructions-Blender

Get Hamilton Beach HBS1200 - Commercial Revolution Ice-Shaver Blender PDF manuals and user guides
UPC - 040094908394
View all Hamilton Beach HBS1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Caring for the Ice Shaver/Blender Cleaning Instructions-Blender wWARNING wWARNING Electrical Shock Hazard Plug into a grounded outlet. Do not remove ground. Do not use an adapter. Do not use an extension cord. Do not immerse base in water or other liquid. Failure to follow these instructions can result in death, fire, or electrical shock. General cleaning Do not allow food residue to dry on any part of the blender. Wash and rinse container, blender blade assembly and base after each use, or whenever it will not be used again within one hour, as follows: 1. Remove the container from the base. Add cleaning solution to the container. Use a washing solution of hot water (less than 115° F/46° C) and a non-sudsing detergent. Use the recommended amount of detergent. 2. Scrub and flush out the container interior to remove food residue. Empty container. 3. Fill container 1⁄4 full with fresh washing solution and place it on the base. 4. Run the blender on high speed for 2 minutes. 5. Repeat step 3 using clean rinse water (95° F/35° C). 6. Wipe down the container with a soft cloth or sponge, dampened with fresh washing solution. 7. Wipe the exterior of the base with a damp cloth or sponge. The base contains electrical components: do not immerse, use a high-pressure washer, or use a dishwasher to clean the base. Cut Hazard Always place cover on jar when blending. Do not put hands, spoons or other utensils in jar when blending. Failure to follow these instructions can result in broken bones or cuts. Sanitizing 1. Wash container as instructed in "General Cleaning." 2. Fill container with sanitizing solution (See "Recommended Sanitizing Solution") and place on base. 3. Run on blender base for 2 minutes. Empty container. 4. Wipe the container exterior with a soft cloth or sponge dampened with sanitizing solution. 5. Immerse the cover and filler cap in sanitizing solution for two minutes. 6. Remove any remaining moisture from cutter assembly by placing empty container on base and running on PULSE for two seconds. 7. When ready to use, rinse with clean water. NOTE: Do not rinse container, cover or filler cap after sanitizing. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Caring for the Ice Shaver/Blender
12
Cleaning Instructions–Blender
General cleaning
Do not allow food residue to dry on any part of the
blender. Wash and rinse container, blender blade
assembly and base after each use
, or whenever it
will not be used again within one hour, as follows:
1.
Remove the container from the base. Add
cleaning solution to the container. Use a washing
solution of hot water (less than 115° F/46° C) and
a non-sudsing detergent. Use the recommended
amount of detergent.
2.
Scrub and flush out the container interior to
remove food residue. Empty container.
3.
Fill container
1
±
4
full with fresh washing solution
and place it on the base.
4.
Run the blender on high speed for 2 minutes.
5.
Repeat step 3 using clean rinse water
(95° F/35° C).
6.
Wipe down the container with a soft cloth or
sponge, dampened with fresh washing solution.
7.
Wipe the exterior of the base with a damp cloth
or sponge. The base contains electrical
components: do not immerse, use a
high-pressure washer, or use a dishwasher
to clean the base.
Sanitizing
1.
Wash container as instructed in “General
Cleaning.”
2.
Fill container with sanitizing solution (See
“Recommended Sanitizing Solution”) and
place on base.
3.
Run on blender base for 2 minutes.
Empty container.
4.
Wipe the container exterior with a soft cloth or
sponge dampened with sanitizing solution.
5.
Immerse the cover and filler cap in sanitizing
solution for two minutes.
6.
Remove any remaining moisture from cutter
assembly by placing empty container on base
and running on PULSE for two seconds.
7.
When ready to use, rinse with clean water.
NOTE:
Do not rinse container, cover or filler cap
after sanitizing.
w
WARNING
Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove ground.
Do not use an adapter.
Do not use an extension cord.
Do not immerse base in water or
other liquid.
Failure to follow these instructions can
result in death, fire, or electrical shock.
w
WARNING
Cut Hazard
Always place cover on jar when blending.
Do not put hands, spoons or other utensils
in jar when blending.
Failure to follow these instructions can
result in broken bones or cuts.