Hayward Ecommand W/2Gva/Base/Aquaconne ECOMMAND-4-Installation-Manual-092419AR - Page 23

Lights Relay, Lights Interlock, Lights Freeze Protection, Lights Pump Speed

Get Hayward Ecommand W/2Gva/Base/Aquaconne PDF manuals and user guides View all Hayward Ecommand W/2Gva/Base/Aquaconne manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Super Chlorinate - if "Chlorinator" is enabled, this option allows the user to start a Super Chlorinate cycle when the Lights button is pressed, rather than using the Settings Menu. Note that only one button can be assigned to this function. Lights Relay This feature allows the user to select either "Standard" (default) or "Dimmer" type relay for the Lights output. The optional AQL-DIM dimmer kit must be installed if "Dimmer" is desired. When "Dimmer" is selected, and the Lights output is manually turned on, the "+" and "-" buttons adjust the level from 20% to 100% (default). The level is saved for the next time the lights are turned from off to on. Lights Interlock If enabled, this feature will override the function (Manual On/Off, Countdown Timer, Timeclock) selected above and turn the lights relay off when: filter pump is off, first 3 minutes of filter pump operation (allows the pump to prime and get water flowing), when the pool/spa suction return valves are in any position other than "pool only", or for the first 3 minutes after solar turns on (allows air in the solar panels to be purged). Interlock is not available for solar, low speed filter pump, super chlorinate or dimmer. Lights Freeze Protection This function helps protect equipment that is wired to the lights relay against freeze damage. If Freeze Protection is enabled and the AIR temperature falls below the selected freeze temperature threshold, the ECOMMAND 4 will energize the lights relay. IMPORTANT: this only enables operation of the lights relay during freeze--see the "Filter Pump Config." menu to enable freeze protection for the main circulation system. Lights Pump Speed This is the speed of the pump when the Lights output is on. The choices are the Settings Menu speed and a speed that is unique to the Lights output only. The default selection is in the "Settings Menu". This is the speed of the pump that has been selected in the Settings Menu for normal filter operation. If an alternate speed is desired when the Lights output is on, push "+" or "-" and select from "Lowest" to "Highest" in 5% increments. 22 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
22
Super Chlorinate
– if “Chlorinator” is enabled, this option allows the user to start a Su-
per Chlorinate cycle when the Lights button is pressed, rather than using the Settings
Menu.
Note that only one button can be assigned to this function.
Lights Relay
This feature allows the user to select either “Standard” (default) or “Dimmer” type relay
for the Lights output.
The optional AQL-DIM dimmer kit must be installed if “Dimmer” is
desired.
When “Dimmer” is selected, and the Lights output is manually turned on, the
“+” and “-” buttons adjust the level from 20% to 100% (default).
The level is saved for
the next time the lights are turned from off to on.
Lights Interlock
If enabled, this feature will override the function (Manual On/Off, Countdown Timer,
Timeclock) selected above and turn the lights relay off when:
filter pump is off, first
3 minutes of filter pump operation (allows the pump to prime and get water flowing),
when the pool/spa suction return valves are in any position other than “pool only”, or
for the first 3 minutes after solar turns on (allows air in the solar panels to be purged).
Interlock is not available for solar, low speed filter pump, super chlorinate or dimmer.
Lights Freeze Protection
This function helps protect equipment that is wired to the lights relay against freeze
damage.
If Freeze Protection is enabled and the AIR temperature falls below the
selected freeze temperature threshold, the ECOMMAND 4 will energize the lights relay.
IMPORTANT:
this only enables operation of the lights relay during freeze--see the
“Filter Pump Config.” menu to enable freeze protection for the main circulation system.
Lights Pump Speed
This is the speed of the pump when the Lights output is on.
The choices are the
Settings Menu speed and a speed that is unique to the Lights output only.
The default
selection is in the “Settings Menu”.
This is the speed of the pump that has been
selected in the Settings Menu for normal filter operation. If an alternate speed is desired
when the Lights output is on, push “+” or “-” and select from “Lowest” to “Highest” in
5% increments.