HP 10/100-TX Intel PRO/100 Intel LAN cards (D6507A, D6508A), Installation Guid - Page 21

HP Support Services

Get HP 10/100-TX Intel PRO/100 PDF manuals and user guides View all HP 10/100-TX Intel PRO/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

HP 10/100 Intel® EtherExpressTM PRO/100+Management Adapter Installation Guide HP Support Services The PC Cannot Be Started or Woken up from the Network Check that the WOL connector cable is connected to the network interface card and to the PC's system board. • If the PC has been powered off (for example, due to an electrical power failure, or because the power cord has been removed), the Remote Power On (RPO) will not work. To enable the RPO, you must first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut down the PC. • Check that the WOL connector cable is connected to the network interface card and to the PC's system board. • Check that the LAN-specific fields in the HP PC Setup utility are correctly set (refer to "Updating LAN-specific Fields in the HP PC Setup Utility" on page 9). NOTE RPO is only supported under Windows 95 and Windows NT 4.0. HP Support Services The latest drivers and utilities are available on HP's Web site at: http://www.hp.com/go/vectrasupport English 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
English
17
HP 10/100 Intel
®
EtherExpress
TM
PRO/100+Management Adapter Installation Guide
HP Support Services
The PC Cannot Be Started or Woken up from the Network
Check that the WOL connector cable is connected to the network
interface card and to the PC’s system board.
•
If the PC has been powered off (for example, due to an electrical
power failure, or because the power cord has been removed), the
Remote Power On (RPO) will not work. To enable the RPO, you must
first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut
down the PC.
•
Check that the WOL connector cable is connected to the network
interface card and to the PC’s system board.
•
Check that the LAN-specific fields in the HP PC
Setup
utility are
correctly set (refer to “Updating LAN-specific Fields in the HP PC
Setup Utility” on page 9).
NOTE
RPO is only supported under Windows 95 and Windows NT 4.0.
HP Support Services
The latest drivers and utilities are available on HP’s Web site at: