HP 6210 HP Officejet 6200 series all-in-one - (English) User Guide - Page 119

Clean the area around the ink nozzles, HP Image Zone - officejet power cord

Page 119 highlights

Chapter 14 3 Lightly press down on the print cartridge to release it, and then pull it toward you out of the slot. Note Do not remove both print cartridges at the same time. Remove and clean each print cartridge one at a time. Do not leave a print cartridge outside the HP all-in-one for more than 30 minutes. 4 Inspect the print cartridge contacts for ink and debris buildup. 5 Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any excess water from it. 6 Hold the print cartridge by its sides. 7 Clean only the copper-colored contacts. For information on cleaning the ink nozzle area, see Clean the area around the ink nozzles. 1 Copper-colored contacts 2 Ink nozzles (do not clean) 8 Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks into place. 9 Repeat if necessary for the other print cartridge. 10 Gently close the print-carriage access door and plug the power cord into the back of the HP all-in-one. Clean the area around the ink nozzles If the HP all-in-one is used in a dusty environment, a small amount of debris might accumulate inside the device. This debris can include dust, hair, carpet, or clothing fibers. When debris gets on the print cartridges, it can cause ink streaks and smudges on printed pages. Ink streaking can be corrected by cleaning around the ink nozzles as described here. Note Clean the area around the ink nozzles only if you continue to see streaks and smudges on your printed pages after you have already cleaned the print cartridges by using the control panel or the HP Image Zone. For more information, see Clean the print cartridges. 116 HP Officejet 6200 series all-in-one

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177

3
Lightly press down on the print cartridge to release it, and then pull it toward you
out of the slot.
Note
Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the
HP all-in-one for more than 30 minutes.
4
Inspect the print cartridge contacts for ink and debris buildup.
5
Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze
any excess water from it.
6
Hold the print cartridge by its sides.
7
Clean only the copper-colored contacts. For information on cleaning the ink
nozzle area, see
Clean the area around the ink nozzles
.
1
Copper-colored contacts
2
Ink nozzles (do not clean)
8
Slide the print cartridge back into the slot. Push the print cartridge forward until it
clicks into place.
9
Repeat if necessary for the other print cartridge.
10
Gently close the print-carriage access door and plug the power cord into the back
of the HP all-in-one.
Clean the area around the ink nozzles
If the HP all-in-one is used in a dusty environment, a small amount of debris might
accumulate inside the device. This debris can include dust, hair, carpet, or clothing
fibers. When debris gets on the print cartridges, it can cause ink streaks and smudges
on printed pages. Ink streaking can be corrected by cleaning around the ink nozzles
as described here.
Note
Clean the area around the ink nozzles only if you continue to see streaks and
smudges on your printed pages after you have already cleaned the print cartridges by
using the control panel or the
HP Image Zone
. For more information, see
Clean the
print cartridges
.
Chapter 14
116
HP Officejet 6200 series all-in-one