HP Brio ba210 hp brio ba210, user guide - Page 34

There's a Problem with the Floppy Drive

Get HP Brio ba210 PDF manuals and user guides View all HP Brio ba210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Hardware Problems There's a Problem with the Floppy Drive Have you checked that... You are using a formatted diskette and it is inserted correctly Ö How You will receive an on-screen error if the diskette is not properly formatted The floppy is clean Ö Use a diskette cleaning kit (see your PC dealer) The Setup program is correctly configured for your floppy drive The hardware is working properly Ö Ö Enter the Setup program by pressing F2 at startup, then: • Go to the Advanced menu. Make sure you have enabled Floppy Disk Controller. • Go to the Main menu. You should see 1.44 M, 3.5 in. in the Legacy Diskette A field. Run DiagTools to see if it detects a problem with the floppy drive (refer to page 42) Advanced Troubleshooting The drive's power and data cables are correctly connected Check that the drive's power and data cables are correctly connected at both ends (floppy drive and system board). Refer to page 55 for connections to the floppy drive and page 53 for connections to the system board. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Hardware Problems
26
There’s a Problem with the Floppy Drive
Have you checked that...
How
You are using a formatted diskette and it is inserted
correctly
Ö
You will receive an on-screen error if the
diskette is not properly formatted
The floppy is clean
Ö
Use a diskette cleaning kit (see your PC
dealer)
The
Setup
program is correctly configured for your
floppy drive
Ö
Enter the
Setup
program by pressing
F2
at
startup, then:
•
Go to the
Advanced
menu. Make sure
you have enabled
Floppy Disk
Controller
.
•
Go to the
Main
menu. You should see
1.44 M, 3.5 in
. in the
Legacy Diskette
A
field.
The hardware is working properly
Ö
Run DiagTools to see if it detects a problem
with the floppy drive (refer to page 42)
Advanced Troubleshooting
The drive’s power and data cables are correctly
connected
Check that the drive’s power and data cables
are correctly connected at both ends (floppy
drive and system board). Refer to page 55 for
connections to the floppy drive and page 53
for connections to the system board.