HP Business Inkjet 2300 HP Business Inkjet 2300 - User Guide - Page 112

Cfg Tcp/ip, Bootp=yes, Dhcp=yes, Bootp=no, Dhcp=no, Auto Ip=yes, Cfg Link, 100tx Half, Security, Reset

Get HP Business Inkjet 2300 PDF manuals and user guides View all HP Business Inkjet 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

A-10 Message CFG TCP/IP CFG LINK WEB SECURITY Value or Submenu NO YES NO YES HTTPS HTTP/HTTPS KEEP RESET Description Selects whether to use the TCP/IP menu and set the TCP/IP protocol parameters. In the TCP/IP menu, you can specify BOOTP=YES or DHCP=YES for TCP/IP parameters to be automatically configured by a BootP or DHCP server when the printer is turned on. If you specify BOOTP=NO and DHCP=NO, you can choose AUTO IP=YES to have a link-local address 169.254.x.x assigned automatically. If you specify BOOTP=NO, DHCP=NO, and AUTO IP=NO, you can manually set the following TCP/IP parameters from the control panel: z IP address (IP) z Subnet Mask (SM) z Syslog Server (LG) z Default Gateway (GW) z Idle Timeout period (default is 270 seconds; 0 disables the timeout) When setting IP numbers, press (up arrow button) to increase the number by 1. Press (down arrow button) to decrease the number by 1. Press (select button) to make your selection. Selects whether you want to manually configure the HP Jetdirect 10/100Base-TX print server's network link speed and communication mode. The HP Jetdirect settings must match the network. The default setting is NO, which bypasses the link configuration menu items. If you specify YES, you can select one of the following link configuration menu items: z AUTO (default): The print server automatically configures itself to match the link speed and communication mode of the network. If it fails, 100TX HALF will be set. z 10T HALF: 10 Mbps, half-duplex operation z 10T FULL: 10 Mbps, full-duplex operation z 100TX HALF: 100 Mbps, half-duplex operation z 100TX FULL: 100 Mbps, full-duplex operation For configuration management, specify whether the embedded Web server will accept communications using HTTPS (Secure HTTP) only, or both HTTP and HTTPS. z HTTPS: For secure, encrypted communications, only HTTPS access is accepted. The print server will appear as a secure site. z HTTP/HTTPS: Access using either HTTP or HTTPS is permitted. Specify whether the current security settings on the print server will be saved or reset to factory defaults. z KEEP (default): The current security settings are maintained. z RESET: Security settings are reset to factory defaults. ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
A
-
10
ENWW
CFG TCP/IP
NO
YES
Selects whether to use the TCP/IP menu and set the
TCP/IP protocol parameters.
In the TCP/IP menu, you can specify
BOOTP=YES
or
DHCP=YES
for TCP/IP parameters to be
automatically configured by a BootP or DHCP server
when the printer is turned on.
If you specify
BOOTP=NO
and
DHCP=NO
, you can
choose
AUTO IP=YES
to have a link-local address
169.254.x.x assigned automatically.
If you specify
BOOTP=NO
,
DHCP=NO
, and
AUTO IP=NO
, you can manually set the following
TCP/IP parameters from the control panel:
IP address (IP)
Subnet Mask (SM)
Syslog Server (LG)
Default Gateway (GW)
Idle Timeout period (default is 270 seconds; 0
disables the timeout)
When setting IP numbers, press
(up arrow
button) to increase the number by 1. Press
(down
arrow button) to decrease the number by 1. Press
(select button)
to make your selection.
CFG LINK
NO
YES
Selects whether you want to manually configure the
HP Jetdirect 10/100Base-TX print server’s network
link speed and communication mode.
The HP Jetdirect settings must match the network.
The default setting is
NO
, which bypasses the link
configuration menu items.
If you specify
YES
, you can select one of the
following link configuration menu items:
AUTO
(default): The print server automatically
configures itself to match the link speed and
communication mode of the network. If it fails,
100TX HALF
will be set.
10T HALF
: 10 Mbps, half-duplex operation
10T FULL
: 10 Mbps, full-duplex operation
100TX HALF
: 100 Mbps, half-duplex operation
100TX FULL
: 100 Mbps, full-duplex operation
WEB
HTTPS
HTTP/HTTPS
For configuration management, specify whether the
embedded Web server will accept communications
using HTTPS (Secure HTTP) only, or both HTTP
and HTTPS.
HTTPS
: For secure, encrypted communications,
only HTTPS access is accepted. The print
server will appear as a secure site.
HTTP/HTTPS
: Access using either HTTP or
HTTPS is permitted.
SECURITY
KEEP
RESET
Specify whether the current security settings on the
print server will be saved or reset to factory defaults.
KEEP
(default): The current security settings are
maintained.
RESET
: Security settings are reset to factory
defaults.
Message
Value or Submenu
Description