HP Chromebox G3 Maintenance and Service Guide - Page 40

terminal. The #2/Aux, 1/Main, 2/Aux

Get HP Chromebox G3 PDF manuals and user guides View all HP Chromebox G3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

1. Prepare the Chromebox for disassembly (Preparation for disassembly on page 27). 2. Remove the bottom cover (Bottom cover on page 27). 3. Remove the I/O side frame (I/O side frame on page 28). 4. Remove the bottom shield (Bottom shield on page 29). When you replace the system board, be sure to remove the following components from the defective system board and install them on the replacement system board: ● WLAN module (see WLAN module on page 31) ● Solid-state drive (see Solid-state drive on page 33) ● Memory module and shield (see Memory module on page 33) ● Fan (see Fan on page 37) ● Heat sink (see Heat sink on page 38) Remove the system board: 1. Disconnect the WLAN antenna cables (1) from the WLAN module terminals. NOTE: The #1/Main WLAN antenna cable connects to the WLAN module #1/Main terminal. The #2/Aux WLAN antenna cable connects to the WLAN module #2/Aux terminal. 2. Disconnect the power button board cable (2) from the system board. 36 Chapter 6 Removal and replacement procedures for authorized service provider parts ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
1.
Prepare the Chromebox for disassembly (
Preparation for disassembly
on page
27
).
2.
Remove the bottom cover (
Bottom cover
on page
27
).
3.
Remove the I/O side frame (
I/O side frame
on page
28
).
4.
Remove the bottom shield (
Bottom shield
on page
29
).
When you replace the system board, be sure to remove the following components from the defective system
board and install them on the replacement system board:
●
WLAN module (see
WLAN module
on page
31
)
●
Solid-state drive (see
Solid-state drive
on page
33
)
●
Memory module and shield (see
Memory module
on page
33
)
●
Fan (see
Fan
on page
37
)
●
Heat sink (see
Heat sink
on page
38
)
Remove the system board:
1.
Disconnect the WLAN antenna cables
(1)
from the WLAN module terminals.
NOTE:
The #1/Main WLAN antenna cable connects to the WLAN module
#1/Main
terminal. The #2/Aux
WLAN antenna cable connects to the WLAN module
#2/Aux
terminal.
2.
Disconnect the power button board cable
(2)
from the system board.
36
Chapter 6
Removal and replacement procedures for authorized service provider parts
ENWW