HP EliteBook 800 EliteBook 820 G4 Notebook PC EliteBook 828 G4 Notebook PC Mai - Page 57

Lift the ZIF connector, Open the computer as far as possible.

Get HP EliteBook 800 PDF manuals and user guides View all HP EliteBook 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

1. Position the computer upside down. 2. Remove the 2 broadhead Phillips M2.5×2.5 screws that secure the keyboard to the computer (1). NOTE: The screws are labeled with a keyboard symbol. 3. Position the computer on its side and partially open. 4. Insert a screwdriver or similar thin tool into the hole beside the heat sink/fan assembly, and then press on the back of the keyboard until it disengages from the computer (2). Rotate the top of the keyboard upward, and then lift the keyboard up at an angle to disengage the tabs at the bottom of the keyboard. NOTE: Cables connect the bottom of the keyboard to the system board. Make sure not to prematurely pull the keyboard cables out of the system board connectors. 5. Position the computer upright with the front toward you. 6. Open the computer as far as possible. 7. Slide the keyboard slightly downward, and then lift and rotate the keyboard over onto the palm rest (1). 8. Lift the ZIF connector (2) for the pointing stick cable connector, then and remove the cable from the connector (3). 9. Lift the ZIF connector (4) for the keyboard backlight cable connector, and then remove the cable from the connector (5). 10. Lift the ZIF connector (6) for the keyboard cable connector, and then remove the cable from the connector (7). Component replacement procedures 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
1.
Position the computer upside down.
2.
Remove the 2 broadhead Phillips M2.5×2.5 screws that secure the keyboard to the computer
(1)
.
NOTE:
The screws are labeled with a keyboard symbol.
3.
Position the computer on its side and partially open.
4.
Insert a screwdriver or similar thin tool into the hole beside the heat sink/fan assembly, and then press
on the back of the keyboard until it disengages from the computer
(2)
. Rotate the top of the keyboard
upward, and then lift the keyboard up at an angle to disengage the tabs at the bottom of the keyboard.
NOTE:
Cables connect the bottom of the keyboard to the system board. Make sure not to prematurely
pull the keyboard cables out of the system board connectors.
5.
Position the computer upright with the front toward you.
6.
Open the computer as far as possible.
7.
Slide the keyboard slightly downward, and then lift and rotate the keyboard over onto the palm rest
(1)
.
8.
Lift the ZIF connector
(2)
for the pointing stick cable connector, then and remove the cable from the
connector
(3)
.
9.
Lift the ZIF connector
(4)
for the keyboard backlight cable connector, and then remove the cable from
the connector
(5)
.
10.
Lift the ZIF connector
(6)
for the keyboard cable connector, and then remove the cable from the
connector
(7)
.
Component replacement procedures
47