HP Envy 15-1000se HP ENVY 15 - Maintenance and Service Guide - Page 59

Remove the four Phillips PM3.0×4.0 screws, that secure the hard drive bracket to the hard drive.

Get HP Envy 15-1000se PDF manuals and user guides View all HP Envy 15-1000se manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Removal and replacement procedures Remove the hard drive: 1. Disconnect the hard drive cable 1 from the system board. 2. Remove the two Phillips PM2.0×4.0 broadhead screws 2 that secure the hard drive to the base enclosure. 3. Remove the hard drive 3. 4. If it is necessary to replace the hard drive cable or bracket: a. Disconnect the hard drive cable 1 from the hard drive. b. Remove the four Phillips PM3.0×4.0 screws 2 that secure the hard drive bracket to the hard drive. c. Remove the hard drive bracket 3. Reverse this procedure to reassemble and install the hard drive. Maintenance and Service Guide 4-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
Removal and replacement procedures
Maintenance and Service Guide
4–21
Remove the hard drive:
1. Disconnect the hard drive cable
1
from the system board.
2. Remove the two Phillips PM2.0×4.0 broadhead screws
2
that secure the hard drive to the base enclosure.
3. Remove the hard drive
3
.
4. If it is necessary to replace the hard drive cable or bracket:
a.
Disconnect the hard drive cable
1
from the hard drive.
b.
Remove the four Phillips PM3.0×4.0 screws
2
that secure the hard drive bracket to the hard drive.
c.
Remove the hard drive bracket
3
.
Reverse this procedure to reassemble and install the hard drive.