HP Jetdirect en1700 HP Jetdirect Print Server Administrator's Guide (Firmware - Page 43

Disables DHCP requests - firmware

Get HP Jetdirect en1700 - IPv4/IPv6 Print Server PDF manuals and user guides View all HP Jetdirect en1700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Table 3-2 TFTP Configuration File Parameters (continued) default-ip-dhcp: Specifies whether DHCP requests will be periodically transmitted when a legacy default IP address 192.0.0.192 or linklocal IP address 169.254.x.x has been automatically assigned. 0: Disables DHCP requests. 1 (default): Enables DHCP requests. dhcp-arbitration: Specifies the amount of time, in seconds, that the print server will wait for DHCP configuration offers. A value from 1 to 10 may be set. The default is 5 seconds. phone-home-config: Specifies privacy settings on the print server during embedded Web server access. This command controls whether statistical data on product use may be sent to HP. For HP to collect data, Internet access is required. 2: Prompt the user to allow sending data on initial access to the Networking tab of the embedded Web server. This is the factory-default and cold-reset value. Once changed, this value cannot be re-selected. 1: Allows the sending of data to HP without prompting the user. 0: Disables sending data to HP without prompting the user. web-refresh: Specifies the time interval (1-99999 seconds) for embedded Web server diagnostic page updates. If set to 0, the refresh rate is disabled. SNMP snmp-config: Enables or disables SNMP operation on the print server. 0 disables, 1 (default) enables SNMP. CAUTION: Disabling SNMP will disable all SNMP agents (SNMP v1, v2, v3) as well as communications with HP Web Jetadmin. In addition, firmware upgrades through current HP downloading utilities will be disabled. get-cmnty-name: (or get-community-name:) Specifies a password that determines which SNMP GetRequests the HP Jetdirect print server will respond to. This is optional. If a user-specified get community name is set, the print server will respond to either a user-specified community name or the factory-default. The community name must be ASCII characters. The maximum length is 255 characters. set-cmnty-name: (or set-community-name:) Specifies a password that determines which SNMP SetRequests (control functions) the HP Jetdirect print server will respond to. The community name of an incoming SNMP SetRequest must match the print server's "set community name" for the print server to respond. (For additional security, you may limit configuration access through the print server's host access list). Community names must be ASCII characters. The maximum length is 255 characters. auth-trap: (or authentication-trap:) Configures the print server to send (on) or not send (off) SNMP authentication traps. Authentication traps indicate that an SNMP request was received, but the community name check failed. The default is "on." trap-dest: (or trap-destination:) Enters a host's IP address into the HP Jetdirect print server's SNMP trap destination list. The command format is: trap-dest: [community name] [port number] The default community name is "public"; the default SNMP port number is "162". The port number cannot be specified without a community name. ENWW IPv4 Configuration 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
default-ip-dhcp:
Specifies whether DHCP requests will be periodically transmitted when a legacy default IP address 192.0.0.192 or link-
local IP address 169.254.x.x has been automatically assigned.
0
: Disables DHCP requests.
1
(default): Enables DHCP requests.
dhcp-arbitration:
Specifies the amount of time, in seconds, that the print server will wait for DHCP configuration offers. A value from 1 to
10 may be set. The default is 5 seconds.
phone-home-config:
Specifies privacy settings on the print server during embedded Web server access. This command controls whether
statistical data on product use may be sent to HP. For HP to collect data, Internet access is required.
2
: Prompt the user to allow sending data on initial access to the Networking tab of the embedded Web server. This is the
factory-default and cold-reset value. Once changed, this value cannot be re-selected.
1
: Allows the sending of data to HP without prompting the user.
0
: Disables sending data to HP without prompting the user.
web-refresh:
Specifies the time interval (1–99999 seconds) for embedded Web server diagnostic page updates. If set to
0
, the refresh
rate is disabled.
SNMP
snmp-config:
Enables or disables SNMP operation on the print server.
0
disables,
1
(default) enables SNMP.
CAUTION:
Disabling SNMP will disable all SNMP agents (SNMP v1, v2, v3) as well as communications with
HP Web Jetadmin. In addition, firmware upgrades through current HP downloading utilities will be disabled.
get-cmnty-name:
(or
get-community-name:
)
Specifies a password that determines which SNMP GetRequests the HP Jetdirect print server will respond to. This is
optional. If a user-specified get community name is set, the print server will respond to either a user-specified community
name or the factory-default. The community name must be ASCII characters. The maximum length is 255 characters.
set-cmnty-name:
(or
set-community-name:
)
Specifies a password that determines which SNMP SetRequests (control functions) the HP Jetdirect print server will
respond to. The community name of an incoming SNMP SetRequest must match the print server's “set community name”
for the print server to respond. (For additional security, you may limit configuration access through the print server's host
access list). Community names must be ASCII characters. The maximum length is 255 characters.
auth-trap:
(or
authentication-trap:
)
Configures the print server to send (on) or not send (off) SNMP authentication traps. Authentication traps indicate that an
SNMP request was received, but the community name check failed. The default is “on.”
trap-dest:
(or
trap-destination:
)
Enters a host's IP address into the HP Jetdirect print server's SNMP trap destination list. The command format is:
trap-dest: <ip-address> [community name] [port number]
The default community name is “
public
”; the default SNMP port number is “162”. The port number cannot be specified
without a community name.
Table 3-2
TFTP Configuration File Parameters (continued)
ENWW
IPv4 Configuration
33