HP LH4r HP Netserver LPr Rack Cabling Guide - Page 10

WARNING, Install Fans if Required and UPS First If You Have Them, Mount Components in the Rack, Plan

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Chapter 1 About This Cabling Reference NOTE HP Rack System product numbers J1487B, J1487B option AXH, and J1488A require door hardware to be in place before mounting components. If you are using front or rear doors, be sure the hinge and latch hardware is mounted before putting on any other hardware. This prevents later disassembly. WARNING When the back door of a rack is removed, the latch catch bracket protrudes. To avoid injury, temporarily remove this bracket prior to installing components into the rear of the rack. 3. If present, remove side panels to allow better access. Follow instructions shipped with the rack to do so. Install Fans if Required and UPS First If You Have Them 1. If an extractor fan unit is to be used, install it following instructions which accompany the unit. NOTE The LPr has an internal fan system, so rack doors must be perforated (front and/or rear). As longs as the doors are perforated, an extractor fan panel is not necessary. 2. If an Uninterruptible Power Supply (UPS) is used, install the UPS mounting rails and fasten the unit into place following instructions which accompany it. Place UPS equipment in the lowest EIA Units of the rack. Plug the UPS in to charge the batteries as soon as possible. 6. Mount Components in the Rack Plan Component Locations Use the original ordering information to locate where each component goes in the rack. If the original ordering information is not available, use HP rack configuration tools to plan the location of each component. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 1
About This Cabling Reference
6
NOTE
HP Rack System product numbers J1487B, J1487B option
AXH, and J1488A
require door hardware to be in place before
mounting components. If you are using front or rear doors, be
sure the hinge and latch hardware is mounted before putting
on any other hardware. This prevents later disassembly.
WARNING
When the back door of a rack is removed, the latch catch
bracket protrudes. To avoid injury, temporarily remove this
bracket prior to installing components into the rear of the
rack.
3.
If present, remove side panels to allow better access. Follow instructions
shipped with the rack to do so.
Install Fans if Required and UPS First If You Have Them
1.
If an extractor fan unit is to be used, install it following instructions which
accompany the unit.
NOTE
The LPr has an internal fan system, so rack doors must be
perforated (front and/or rear). As longs as the doors are
perforated, an extractor fan panel is not necessary.
2.
If an Uninterruptible Power Supply (UPS) is used, install the UPS
mounting rails and fasten the unit into place following instructions
which accompany it. Place UPS equipment in the lowest EIA Units of the
rack. Plug the UPS in to charge the batteries as soon as possible.
6.
Mount Components in the Rack
Plan Component Locations
Use the original ordering information to locate where each component goes in
the rack.
If the original ordering information is not available, use HP rack configuration
tools to plan the location of each component.