HP LH4r Pedestal-to-Rack Conversion Guide - Page 18

Lighten the NetServer, Remove Hot-Swap Hard Disk Drives

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 2 Remove Bezel, Cover, and Components Lighten the NetServer Before you lift the NetServer, remove the hot-swap hard disk drives and power supply modules. This will lighten the NetServer, so that fewer people will be needed to lift it. WARNING Do not attempt to lift the NetServer by yourself. Follow all local regulations when moving the NetServer. Failure to observe this warning could result in serious injury to personnel or damage to the NetServer. Take out power supplies and hot-swap hard disk drives before lifting the NetServer. The HP NetServer LH 3r weighs up to 115 pounds (73 kg) when fully loaded. The HP NetServer LH 4r weighs up to 176 pounds (80 kg) when fully loaded. The HP NetServer LH 3000r weighs up to 118 pounds (54 kg) when fully loaded. The HP NetServer LH 6000r weighs up to 180 pounds (80 kg) when fully loaded. Remove Hot-Swap Hard Disk Drives CAUTION Wear a wrist strap and use a static-dissipating work surface connected to the chassis when you remove or install hot-swap disk drive modules. 1. Refer to Figure 2-3. To unlock the drive, push the locking latch in and then pull the ejector handle toward you. 2. Gently pull the drive out about an inch to disengage the power connection. 3. Use your hand to support the bottom of the drive. Slowly pull the drive straight out. Do not allow the drive to fall. 4. Place the drive in an electrostatic-protected container or on an electrostaticprotected surface. Do not stack drives. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 2
Remove Bezel, Cover, and Components
14
Lighten the NetServer
Before you lift the NetServer, remove the hot-swap hard disk drives and power
supply modules. This will lighten the NetServer, so that fewer people will be
needed to lift it.
WARNING
Do not attempt to lift the NetServer by yourself. Follow all
local regulations when moving the NetServer.
Failure to observe this warning could result in serious injury to
personnel or damage to the NetServer.
Take out power supplies and hot-swap hard disk drives before
lifting the NetServer.
The HP NetServer LH 3r weighs up to 115 pounds (73 kg)
when fully loaded. The HP NetServer LH 4r weighs up to
176 pounds (80 kg) when fully loaded.
The HP NetServer LH 3000r weighs up to 118 pounds (54 kg)
when fully loaded. The HP NetServer LH 6000r weighs up to
180 pounds (80 kg) when fully loaded.
Remove Hot-Swap Hard Disk Drives
CAUTION
Wear a wrist strap and use a static-dissipating work surface
connected to the chassis when you remove or install hot-swap
disk drive modules.
1.
Refer to Figure 2-3. To unlock the drive, push the locking latch in and then
pull the ejector handle toward you.
2.
Gently pull the drive out about an inch to disengage the power connection.
3.
Use your hand to support the bottom of the drive. Slowly pull the drive
straight out.
Do not allow the drive to fall
.
4.
Place the drive in an electrostatic-protected container or on an electrostatic-
protected surface.
Do not stack drives.