HP LH4r Pedestal-to-Rack Conversion Guide - Page 28

Install the NetServer in the Rack, To install into an HP rack

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Chapter 3 Conversion: Install Components, Cover, and Front Bezel Install the NetServer in the Rack Refer to the documentation listed below to install the slides in the rack and to install the NetServer into the rack: • To install into an HP rack: Refer to the NetServer's user guide or installation guide. For cabling instructions, refer to the documentation that came with the rack and either the Rack Cabling Reference for your HP NetServer. • To install into a Compaq Rack: Refer to the HP NetServer LH 3r, LH 4r, LH 3000r, and LH 6000r Installation Guide for Compaq® 4000/7000 Racks. For cabling instructions, refer to the documentation that came with the rack and either the Rack Cabling Reference for your HP NetServer. Refer to this rack documentation for detailed instructions as you do the following: 1. Extend the anti-tip foot or ensure that the anti-tip feature is installed. Lower the leveler feet. WARNING To prevent the rack enclosure from tipping over, • Extend the anti-tip foot or verify that the anti-tip feature is installed. • Verify that the leveler feet are lowered. • DO NOT extend more than one piece of equipment at a time out from the front of the rack. Failure to take these precautions could result in serious injury and equipment damage. 2. If there is a door on the rack, remove it. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 3
Conversion: Install Components, Cover, and Front Bezel
24
Install the NetServer in the Rack
Refer to the documentation listed below to install the slides in the rack and to
install the NetServer into the rack:
•
To install into an HP rack:
Refer to the NetServer's user guide or
installation guide
.
For cabling instructions, refer to the documentation that
came with the rack and either the
Rack Cabling Reference
for your HP
NetServer.
•
To install into a Compaq Rack:
Refer to the
HP NetServer LH 3r, LH 4r,
LH 3000r, and LH 6000r Installation Guide for Compaq
®
4000/7000
Racks.
For cabling instructions, refer to the documentation that came with
the rack and either the
Rack Cabling Reference
for your HP NetServer.
Refer to this rack documentation for detailed instructions as you do the following:
1.
Extend the anti-tip foot or ensure that the anti-tip feature is installed. Lower
the leveler feet.
WARNING
To prevent the rack enclosure from tipping over,
•
Extend the anti-tip foot or verify that the anti-tip feature is
installed.
•
Verify that the leveler feet are lowered.
•
DO NOT extend more than one piece of equipment at a
time out from the front of the rack.
Failure to take these precautions could result in serious injury
and equipment damage.
2.
If there is a door on the rack, remove it.