HP LH4r Pedestal-to-Rack Conversion Guide - Page 29

For HP racks, HP Systems, HP Rack System/E, For Compaq racks, NetServer LH 3r, LH 4r, LH 3000r

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 3 Conversion: Install Components, Cover, and Front Bezel 3. Mark locations on the rack columns for all bar nuts and rack nuts to hold the rack slides and bezel mounting hardware. ◊ For HP racks, use the appropriate rack installation template for your rack: ∗ For HP Systems racks, use the installation template labeled LH 3r (HP Systems), the installation template labeled LH 4r (HP Systems), or the installation template labeled LH 3000r and LH 6000r (HP Systems). ∗ For HP Rack System/E racks and HP Rack System/U racks, use the installation template labeled LH 3r (HP Rack System/E), the installation template labeled LH 4r (HP Rack System/E), or the installation template labeled LH 3000r and LH 6000r (HP Rack System/E). Be sure to mark holes 9 and 13 above the base line for the rack nuts that will hold the chassis retention bracket. ◊ For Compaq racks, count up from the top of the unit below, marking the 20th and 22nd holes on all four columns, as described in the HP NetServer LH 3r, LH 4r, LH 3000r, and LH 6000r Installation Guide for Compaq® 4000/7000 Racks. 4. Install all bar nuts and rack nuts to hold the rack slides and bezel mounting hardware. For HP racks, be sure to install the rack nuts for the chassis retention bracket, as shown in Figure 3-5. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 3
Conversion: Install Components, Cover, and Front Bezel
25
3.
Mark locations on the rack columns for all bar nuts and rack nuts to hold
the rack slides and bezel mounting hardware.
◊
For HP racks,
use the appropriate rack installation template for your
rack
:
∗
For
HP Systems
racks, use the installation template labeled
LH 3r
(HP Systems),
the installation template labeled
LH 4r (HP
Systems)
,
or the installation template labeled
LH 3000r
and LH 6000r
(HP
Systems).
∗
For
HP Rack System/E
racks and
HP Rack System/U
racks, use
the installation template labeled
LH 3r (HP Rack System/E),
the
installation template labeled
LH 4r (HP Rack System/E),
or the
installation template labeled
LH 3000r
and LH 6000r
(HP Rack
System/E).
Be sure to mark holes 9 and 13 above the base line for the rack nuts that
will hold the chassis retention bracket.
◊
For Compaq racks,
count up from the top of the unit below, marking
the 20th and 22nd holes on all four columns, as described in the
HP
NetServer LH 3r, LH 4r, LH 3000r, and LH 6000r Installation Guide
for Compaq
®
4000/7000 Racks
.
4.
Install all bar nuts and rack nuts to hold the rack slides and bezel mounting
hardware.
For HP racks, be sure to install the rack nuts for the chassis retention
bracket, as shown in Figure 3-5.