HP Pavilion 11-s000 Maintenance and Service Guide - Page 42

Hard drive, Remove the Phillips PM2.0×3.3 screw

Get HP Pavilion 11-s000 PDF manuals and user guides View all HP Pavilion 11-s000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module. NOTE: The #1/white WLAN antenna cable connects to the WLAN module #1/Main terminal. The #2/ black WLAN antenna cable connects to the WLAN module #2/Aux terminal. 2. Remove the Phillips PM2.0×3.3 screw (2) that secures the WLAN module to the bottom cover. (The WLAN module tilts up.) 3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve should be placed over the antenna connector, as shown in the following illustration. Reverse this procedure to install the WLAN module. Hard drive Description Hard drive (500-GB, 5400-rpm, SATA, 7.0-mm) NOTE: The hard drive spare part kit does not include the hard drive bracket or hard drive cable adapter. The hard drive bracket and hard drive cable adapter are included in the Hard Drive Hardware Kit, spare part number 837602-001. Spare part number 778186-005 Before removing the hard drive, follow these steps: 34 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
1.
Disconnect the WLAN antenna cables
(1)
from the terminals on the WLAN module.
NOTE:
The #1/white WLAN antenna cable connects to the WLAN module #1/Main terminal. The #2/
black WLAN antenna cable connects to the WLAN module #2/Aux terminal.
2.
Remove the Phillips PM2.0×3.3 screw
(2)
that secures the WLAN module to the bottom cover. (The WLAN
module tilts up.)
3.
Remove the WLAN module
(3)
by pulling the module away from the slot at an angle.
NOTE:
If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve
should be placed over the antenna connector, as shown in the following illustration.
Reverse this procedure to install the WLAN module.
Hard drive
Description
Spare part number
Hard drive (500-GB, 5400-rpm, SATA, 7.0-mm)
NOTE:
The hard drive spare part kit does not include the hard drive bracket or hard drive cable
adapter. The hard drive bracket and hard drive cable adapter are included in the Hard Drive Hardware
Kit, spare part number 837602-001.
778186-005
Before removing the hard drive, follow these steps:
34
Chapter 5
Removal and replacement procedures