HP Pavilion 15-cc600 Maintenance and Service Guide - Page 46

from the keyboard/top cover., Separate the rear edge of the bottom cover

Get HP Pavilion 15-cc600 PDF manuals and user guides View all HP Pavilion 15-cc600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

2. Remove the following screws that secure the bottom cover to the computer: (2) Four Phillips PM2.5×6.7 screws under the rear rubber feet (3) Two Phillips PM2.0×10.7 screws in the middle of the bottom cover (4) Two Phillips PM2.0×5.8 screws under the front rubber feet (5) Two Phillips PM2.0×5.6 screws on the front edge 3. Insert a case utility tool (1) or similar thin, plastic tool into the display hinge areas of the bottom cover. 4. Separate the rear edge of the bottom cover (2) from the keyboard/top cover. 5. Insert a case utility tool (3) or similar thin, plastic tool into the optical drive area of the bottom cover. 6. Separate the tabs (4) built into the keyboard/top cover from the slots built into the bottom cover. 7. Remove the bottom cover (5). 38 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
2.
Remove the following screws that secure the bottom cover to the computer:
(2)
Four Phillips PM2.5×6.7 screws under the rear rubber feet
(3)
Two Phillips PM2.0×10.7 screws in the middle of the bottom cover
(4)
Two Phillips PM2.0×5.8 screws under the front rubber feet
(5)
Two Phillips PM2.0×5.6 screws on the front edge
3.
Insert a case utility tool
(1)
or similar thin, plastic tool into the display hinge areas of the bottom cover.
4.
Separate the rear edge of the bottom cover
(2)
from the keyboard/top cover.
5.
Insert a case utility tool
(3)
or similar thin, plastic tool into the optical drive area of the bottom cover.
6.
Separate the tabs
(4)
built into the keyboard/top cover from the slots built into the bottom cover.
7.
Remove the bottom cover
(5)
.
38
Chapter 5
Removal and replacement procedures