HP Pavilion 15-cc600 Maintenance and Service Guide - Page 64

On computer models equipped with a graphics subsystem with discrete memory, the processor

Get HP Pavilion 15-cc600 PDF manuals and user guides View all HP Pavilion 15-cc600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

2. Remove the heat sink (2). NOTE: Steps 3 and 4 apply to computer models equipped with a graphics subsystem with UMA memory. See Steps 1 and 2 for heat sink removal information for computer models equipped with a graphics subsystem with discrete memory. 3. Remove the four Phillips PM2.0×2.9 screws (1) that secure the heat sink to the system board. 4. Remove the heat sink (2). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits. On computer models equipped with a graphics subsystem with discrete memory: Thermal paste is used on the processor (1) and the heat sink section (2) that services it. Thermal paste is also used on the VGA component (3) and the heat sink section (4) that services it. 56 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
2.
Remove the heat sink
(2)
.
NOTE:
Steps 3 and 4 apply to computer models equipped with a graphics subsystem with UMA
memory. See Steps 1 and 2 for heat sink removal information for computer models equipped with a
graphics subsystem with discrete memory.
3.
Remove the four Phillips PM2.0×2.9 screws
(1)
that secure the heat sink to the system board.
4.
Remove the heat sink
(2)
.
NOTE:
The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system
board components each time the heat sink is removed. Replacement thermal material is included with
the heat sink and system board spare part kits.
On computer models equipped with a graphics subsystem with discrete memory:
Thermal paste is used on
the processor
(1)
and the heat sink section
(2)
that services it. Thermal paste is also used on the VGA
component
(3)
and the heat sink section
(4)
that services it.
56
Chapter 5
Removal and replacement procedures