HP ProLiant MicroServer Gen8 HP ProLiant MicroServer Gen8 User Guide - Page 34

Complete the system setup, Registering the server, Setting up the HP PS1810-8G Switch (optional)

Get HP ProLiant MicroServer Gen8 PDF manuals and user guides View all HP ProLiant MicroServer Gen8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Complete the system setup Check the status of the server LEDs to ensure that the server is operating normally: • System power LED -Solid green • NIC status LED -Solid green • Drive status LED -Solid green • Health LED bar-Solid blue For server management tasks after the initial server setup, use either the dedicated iLO connector (enabled by default) or the NIC 1/shared iLO connector (It is disabled by default. Enable the shared iLO function in iLO RBSU). For more information on iLO management tasks, see the HP website (http://www.hp.com/go/ilomgmtengine/docs). Registering the server To experience quicker service and more efficient support, register the product at the HP Product Registration website (http://register.hp.com). Setting up the HP PS1810-8G Switch (optional) If you intend to use the server with the companion HP PS1810-8G Switch, follow the procedures in this section. For deployments requiring more than eight network ports, HP recommends using the HP PS1810-24G Switch instead of the HP PS1810-8G Switch. For more information on switch-related settings and operational procedures, see the documentation for your switch model on the HP website (http://www.hp.com/networking/support). Setup 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Setup 34
Complete the system setup
Check the status of the server LEDs to ensure that the server is operating normally:
•
System power LED
—Solid green
•
NIC status LED
—Solid green
•
Drive status LED
—Solid green
•
Health LED bar—Solid blue
For server management tasks after the initial server setup, use either the dedicated iLO connector
(enabled by default) or the NIC 1/shared iLO connector
(It is disabled by default. Enable the shared
iLO function in iLO RBSU).
For more information on iLO management tasks, see the HP website
(
).
Registering the server
To experience quicker service and more efficient support, register the product at the HP Product Registration
website (
).
Setting up the HP PS1810-8G Switch (optional)
If you intend to use the server with the companion HP PS1810-8G Switch, follow the procedures in this
section. For deployments requiring more than eight network ports, HP recommends using the HP
PS1810-24G Switch instead of the HP PS1810-8G Switch.
For more information on switch-related settings and operational procedures, see the documentation for your
switch model on the HP website (
).