HP Server rp8420 HP 9000 rp8420 Server - User Service Guide, Fifth Edition - Page 134

Installing the VRM Cover (AB388-00002) and Door Opener (AB388-00003), PA8800 CPUs AB536A and AB537A

Get HP Server rp8420 PDF manuals and user guides View all HP Server rp8420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Flash Current Number Cabinet Name Partition Handle Firmware Version Comments 1 0 PDHC 0A 0 256 A.003.034 Current 2 0 PDHC 0B 0 264 A.003.034 Old 3 0 SFW 0A 0 320 21.001 Pri PA 4 0 SFW 0B 0 328 22.002 Sec PA 5 0 PDHC 1A 0 257 A.003.034 Current 6 0 PDHC 1B 0 265 A.003.034 Old 7 0 SFW 1A 0 321 21.001 Pri PA 8 0 SFW 1B 0 329 21.001 Sec PA Note: You can only duplicate one firmware type at a time. Enter the Entities to be updated (EX: 7,8) : 4 Enter the source entity for the System firmware image: 7 Are you sure that you want to continue(Y/N): y **** Updating device SFW 0B **** Erasing Flash(es). This may take several minutes. DFW has completed successfully for all entities Once DFW has completed, verify the following message is returned: DFW has completed successfully for all entities CAUTION: DO NOT RESET or AC POWER CYCLE the cell or server unless you have received confirmation that DFW has completed successfully. Repeat the dfw command immediately if the firmware failed to complete successfully. 8. Perform steps 11 and 12 from Step 11. Installing the VRM Cover (AB388-00002) and Door Opener (AB388-00003) These two assemblies replace the single CPU cover when installing PA8800 and Dual-Core IPF processors. The assemblies are included in upgrade kits and will not be available to order individually. The following is a list of processors that require the new air baffles. • Intel ® Itanium® 2 CPUs (AB548A and AB439A) • PA8800 CPUs (AB536A and AB537A) Use the following procedure to install new air baffles. 1. Remove the old CPU cover. 2. Install the VRM Cover (AB388-00002), onto the left side of the cell board. Tighten the screw. See Figure 6-22. 134 Removal and Replacement

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
Flash
Current
Number
Cabinet
Name
Partition
Handle
Firmware Version
Comments
------ --------- -------- --------- -------- ------------------ --------
1
0
PDHC 0A
0
256
A.003.034
Current
2
0
PDHC 0B
0
264
A.003.034
Old
3
0
SFW 0A
0
320
21.001
Pri PA
4
0
SFW 0B
0
328
22.002
Sec PA
5
0
PDHC 1A
0
257
A.003.034
Current
6
0
PDHC 1B
0
265
A.003.034
Old
7
0
SFW 1A
0
321
21.001
Pri PA
8
0
SFW 1B
0
329
21.001
Sec PA
Note: You can only duplicate one firmware type at a time.
Enter the Entities to be updated (EX: 7,8) : 4
Enter the source entity for the System firmware image: 7
Are you sure that you want to continue(Y/N): y
**** Updating device SFW 0B ****
Erasing Flash(es). This may take several minutes.
DFW has completed successfully for all entities
Once DFW has completed, verify the following message is returned:
DFW has completed successfully for all entities
CAUTION:
DO NOT RESET
or
AC POWER CYCLE
the cell or server unless you have
received confirmation that DFW has completed successfully. Repeat the
dfw
command
immediately if the firmware failed to complete successfully.
8.
Perform steps 11 and 12 from
Step 11
.
Installing the VRM Cover (AB388-00002) and Door Opener
(AB388-00003)
These two assemblies replace the single CPU cover when installing PA8800 and Dual-Core IPF
processors. The assemblies are included in upgrade kits and will not be available to order
individually. The following is a list of processors that require the new air baffles.
•
Intel
®
Itanium
®
2 CPUs (AB548A and AB439A)
•
PA8800 CPUs (AB536A and AB537A)
Use the following procedure to install new air baffles.
1.
Remove the old CPU cover.
2.
Install the VRM Cover (AB388-00002), onto the left side of the cell board. Tighten the screw.
See
Figure 6-22
.
134
Removal and Replacement