HP Server rp8420 HP 9000 rp8420 Server - User Service Guide, Fifth Edition - Page 145

VRM Cover and Door Opener Installed

Get HP Server rp8420 PDF manuals and user guides View all HP Server rp8420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

Figure 6-36 VRM Cover and Door Opener Installed 17. Position the DIMM cover in place. 18. Tighten the four captive screws to secure the DIMM cover. 19. Install the cell board in the server. 20. Replace the covers. 21. Power on the server. Refer to "Powering down Hardware Components and Powering on the Server" (page 103). 22. Verify the firmware and hardware programmable hardware revisions in "standby" power mode by using the MP:CM>SYSREV command. Below is an example of the minimum firmware version. NOTE: Firmware must be updated to support the new processors. Below is an example of the minimum Firmware Version 3.1. PROGRAMMABLE HARDWARE System Backplane GPM System Backplane FM System Backplane OSP PCI-X Backplane LPM PCI-X Backplane HS Core IO Master Cell LPM Cell PDHC FIRMWARE: Core IO MP Event Dictionary Cell PDHC Cell Pri SFW 1.002 1.002 1.002 2.000 1.000 2.008 1.002 1.007 A.006.012 1.008 A.003.023 22.2 (PA) Removing and Replacing a Central Processing Unit 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
Figure 6-36 VRM Cover and Door Opener Installed
17.
Position the DIMM cover in place.
18.
Tighten the four captive screws to secure the DIMM cover.
19.
Install the cell board in the server.
20.
Replace the covers.
21.
Power on the server. Refer to
“Powering down Hardware Components and Powering on
the Server” (page 103)
.
22.
Verify the firmware and hardware programmable hardware revisions in “standby” power
mode by using the MP:CM>SYSREV command. Below is an example of the minimum
firmware version.
NOTE:
Firmware must be updated to support the new processors. Below is an example
of the minimum Firmware Version 3.1.
PROGRAMMABLE HARDWARE
1.002
System Backplane GPM
1.002
System Backplane FM
1.002
System Backplane OSP
2.000
PCI-X Backplane LPM
1.000
PCI-X Backplane HS
2.008
Core IO Master
1.002
Cell LPM
1.007
Cell PDHC
FIRMWARE:
A.006.012
Core IO MP
1.008
Event Dictionary
A.003.023
Cell PDHC
22.2 (PA)
Cell Pri SFW
Removing and Replacing a Central Processing Unit
145