HP StorageWorks 2/8-EL quickloop fabric assist version 3.0.x user guide - Page 42

Telnet Commands for Configuration 2, The Fabric Assist zone

Get HP StorageWorks 2/8-EL - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/8-EL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Using QuickLoop Fabric Assist Mode In the example shown in Figure 3, second Fabric Assist zone within the fabric has been created. When the telnet command given in the following section is executed: ■ Private host J, connected to port (2,2), can access private targets b and c, and public targets d and e. Private host J cannot see private target b unless b is zoned using its WWN. ■ The port numbers for the private targets are (1,14) and (1,15). Port (1,14) must be zoned using b's WWN, not a port number. ■ The port number for the public target is (2,1). ■ Public target devices d and e are now fully fabric functional and are seen by both host J and host K. Telnet Commands for Configuration 2 1. Log onto the shell admin account on any switch in the fabric. Issue the command: fazoneCreate "FaZone02", "H{2,2}; WWN (target b); 1,15; 2,1" 2. Add the the new zone. For example: cfgAdd "USA" "FaZone02" cfgSave Updating flash... cfgEnable "USA" zone "FaZone02" is in effect The Fabric Assist zone FaZone02, is now part of the effective configuration. 42 Quickloop Fabric Assist User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Using QuickLoop Fabric Assist Mode
42
Quickloop Fabric Assist User Guide
In the example shown in Figure 3, second Fabric Assist zone within the fabric has
been created. When the telnet command given in the following section is
executed:
■
Private host
J
, connected to port (2,2), can access private targets
b
and
c
, and
public targets
d
and
e
.
Private host
J
cannot see private target
b
unless
b
is zoned using its WWN.
■
The port numbers for the private targets are (1,14) and (1,15).
Port (1,14) must be zoned using
b’s
WWN, not a port number.
■
The port number for the public target is (2,1).
■
Public target devices
d
and
e
are now fully fabric functional and are seen by
both host
J
and host
K
.
Telnet Commands for Configuration 2
1.
Log onto the shell
admin
account on any switch in the fabric. Issue the
command:
fazoneCreate “FaZone02”, “H{
2,2}
;
WWN (target b); 1,15; 2,1
”
2.
Add the the new zone. For example:
cfgAdd “USA” “FaZone02”
cfgSave
Updating flash...
cfgEnable “USA”
zone “FaZone02” is in effect
The Fabric Assist zone
FaZone02
, is now part of the effective configuration.