HP Vectra VEi8 HP Vectra VLi8, 3 COM Etherlink III ISA 10BT Card, Installatio - Page 24

Microsoft Windows NT, 0 Workstation, Connecting to a Novell, NetWare 4.11 Server, Requirements,

Page 24 highlights

8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4.0 Workstation 8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4.0 Workstation Connecting to a Novell NetWare 4.11 Server Requirements • HP Vectra with Windows NT 4.0 Workstation. • 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver disk version 6.0. • Driver File: ELNK3ND4.SYS, version 5.26.40 • Microsoft Windows NT 4.0 Workstation media. • Microsoft Windows NT 4.0 Service Pack 4 media. • Novell NetWare 4.11 server that supports IPX network protocol. • Novell IntranetWare Client for Windows NT v4.11b installation media. Device Configuration Device Configuration Interrupt I/O Address Vectra Vli8 05 300 Vectra VEi7 05 300 Vectra VEi8 05 300 Procedure 1 With the HP Vectra turned off, install the 3COM 3C509B network adapter into an ISA slot. 2 Connect network cable media to the 3COM 3C509B network adapter. 3 Power on the machine and boot to a DOS bootable disk. 4 Insert the 3COM 3C509 driver disk and execute "3C5X9CFG.EXE". 5 Select "CONFIGURE NIC" and verify the resource settings listed above under the heading "Device Configuration". 6 If changes are required, save those changes and exit. 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39

8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter
Microsoft Windows NT 4.0 Workstation
8
Installing the 3COM EtherLink III 3C509B ISA 10BT
Network Adapter
Microsoft Windows NT
4.0 Workstation
Connecting to a Novell
NetWare 4.11 Server
Requirements
HP Vectra with Windows NT 4.0 Workstation.
3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver
disk version 6.0.
Driver File: ELNK3ND4.SYS, version 5.26.40
Microsoft Windows NT 4.0 Workstation media.
Microsoft Windows NT 4.0 Service Pack 4 media.
Novell NetWare 4.11 server that supports IPX network protocol.
Novell IntranetWare Client for Windows NT v4.11b installation media.
Device Configuration
Procedure
1
With the HP Vectra turned off, install the 3COM 3C509B network adapter
into an ISA slot.
2
Connect network cable media to the 3COM 3C509B network adapter.
3
Power on the machine and boot to a DOS bootable disk.
4
Insert the 3COM 3C509 driver disk and execute “3C5X9CFG.EXE”.
5
Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.
6
If changes are required, save those changes and exit.
7
Remove the 3COM 3C509B driver disk and reboot the system to Windows
NT.
Device Configuration
Vectra Vli8
Vectra VEi7
Vectra VEi8
Interrupt
05
05
05
I/O Address
300
300
300