HP Vectra VL800 hp vectra vl800, upgrade and installation guide for minitower - Page 28

Removing and Installing a Memory Module, HP Memory, vl800

Get HP Vectra VL800 PDF manuals and user guides View all HP Vectra VL800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2 Installing and Replacing Hardware Parts in Your PC Removing, Replacing and Upgrading Memory Installing or Replacing a Memory Module Memory modules for your PC are available from HP or from your Authorized HP Reseller. To see which memory modules are available, connect to www.hp.com/go/pcaccessories, then select HP Memory and vl800 in the menus. Removing and Installing a Memory Module 1 Switch off the display and PC. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC's cover (refer to page 25 for instructions). 3 Lay the minitower on its side. 4 If you are installing additional memory modules then you will need to remove the continuity modules. Open the two retaining clips and remove the continuity module from the socket. If you are replacing an existing memory module then open the two retaining clips and remove the existing memory module the socket. Always store any removed memory or continuity module in a safe place for future use. 5 Install your new memory modules, ensuring that the two notches on the bottom edge of each memory module is aligned with those of the socket. With the two retaining clips open, press the memory module fully into the socket until the retaining clips click into position. You can also close the retaining clips by hand to ensure that the module is correctly inserted. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
2
Installing and Replacing Hardware Parts in Your PC
Removing, Replacing and Upgrading Memory
Memory modules for your PC are available from HP or from your
Authorized HP Reseller. To see which memory modules are available,
connect to
www.hp.com/go/pcaccessories
, then select
HP Memory
and
vl800
in the menus.
Removing and Installing a Memory Module
Installing or
1
Switch off the display and PC. Disconnect all power cables and any LAN ±
Replacing a
or telecommunications cables.±
Memory Module±
2
Remove the PC’s cover (refer to page 25 for instructions).
3
Lay the minitower on its
side.
4
If you are installing
additional memory
modules then you will
need to remove the
continuity modules. Open
the two retaining clips and
remove the continuity
module from the socket.
If you are replacing an
existing memory module
then open the two
retaining clips and remove the existing memory module the socket
.
Always store any removed memory or continuity module in a safe place
for future use.
5
Install your new memory
modules, ensuring that
the two notches on the
bottom edge of each
memory module is
aligned with those of the
socket. With the two
retaining clips open,
press the memory
module
fully
into the socket until the retaining clips click into position.
You can also close the retaining clips by hand to ensure that the module
is correctly inserted.
28