HP Vectra VL800 hp vectra vl800, upgrade and installation guide for minitower - Page 33

Cables and Connectors (SCSI Models)

Get HP Vectra VL800 PDF manuals and user guides View all HP Vectra VL800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2 Installing and Replacing Hardware Parts in Your PC Installing Mass Storage Devices Cables and Connectors (SCSI Models) 16-bit SCSI Terminator fitted on cable 16-bit Internal U160 68-pin SCSI connector 16-bit SCSI cable with three 68-pin connectors IDE data cable with two connectors for optical drives External 68-pin SCSI connector (two screws) accessible from the rear of the PC. Cable with one 34-pin connector for 3.5-inch Floppy Disk Drive SCSI Card in PCI Slot Secondary IDE Connector Floppy Disk Drive Connector Primary IDE Connector Which SCSI Connectors to Use Models with a SCSI card can be connected to up to three internal SCSI devices. Additional devices can be added outside the PC by connecting directly to the rear panel SCSI connector. The SCSI card allows up to 15 devices to be connected, three internal and 12 external SCSI devices. NOTE The total length of the external SCSI cables should not exceed 3 meters (approximately 10 feet). Before Installing a SCSI Hard Disk (Selected Models Only) If you are installing an additional SCSI drive, you should configure an unused SCSI ID to this accessory. SCSI IDs range from 0 to 15 for Ultrawide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive and SCSI ID 7 is reserved for the integrated SCSI controller (the default for narrow and wide SCSI devices). You should assign an unused SCSI ID to the second SCSI hard disk drive (for example, SCSI ID 1). 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
2
Installing and Replacing Hardware Parts in Your PC
Installing Mass Storage Devices
Cables and Connectors (SCSI Models)
16-bit Internal U160
68-pin SCSI connector
16-bit SCSI Terminator
fitted on cable
SCSI Card in PCI Slot
16-bit SCSI cable
with three 68-pin connectors
IDE data cable with two connectors
for optical drives
Cable with one 34-pin
connector for
3.5-inch Floppy Disk Drive
Floppy Disk Drive Connector
Secondary IDE Connector
External 68-pin SCSI connector (two screws)
accessible from the rear of the PC.
Primary IDE Connector
Which SCSI
Models with a SCSI card can be connected to up to three internal SCSI
Connectors to Use
devices.
Additional devices can be added outside the PC by connecting directly to
the rear panel SCSI connector. The SCSI card allows up to 15 devices to be
connected, three internal and 12 external SCSI devices.
NOTE
The total length of the external SCSI cables should not exceed 3 meters
(approximately 10 feet).
Before Installing a
If you are installing an additional SCSI drive,
you should configure an
SCSI Hard Disk
unused SCSI ID to this accessory.
SCSI IDs range from 0 to 15 for
(Selected Models
Ultrawide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive
Only)
and SCSI ID 7 is reserved for the integrated SCSI controller (the default for
narrow and wide SCSI devices).
You should assign an unused SCSI ID to the second SCSI hard disk drive
(for example, SCSI ID 1).
33