Hoover FH50015 Manual - Page 11

Using the tools

Get Hoover FH50015 PDF manuals and user guides View all Hoover FH50015 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Remove attachment from nozzle and rinse in clear water. Do not remove plastic screen or foam from attachment. A. Powered hand tool has rotating brushes for extra scrubbing action on small carpet areas, carpeted stairs and upholstery. B. Stair/upholstery nozzle has a built-in brush to help provide the scrubbing action some spots may need for removal. How to attach tool All tools connect to the hose in the same manner. 1. Attach tool to connector end of hose by sliding it onto connector until the tab (I) locks it securely. Using your thumb, push forward and up on the latch (J) to remove tool as shown. Before using tool It may be necessary to remove air from the system ("prime the pump") so the clean solution will flow to the tool. Follow these steps: 1. Attach tool to hose and turn the carpet cleaner ON. 2. Put the tool on a hard surface or against your hand to block off the suction. 3. Wait a few seconds (can take up to 15 seconds). Then squeeze the trigger and begin cleaning. Follow the instructions on pages 13 and 14 for the appropriate cleaning task. 5. Drain solution tube by placing round end in sink and raising nozzle above your head. Press the trigger. 6. Proceed with steps c, d and e for "After cleaning" on page 9. Using the tools 3-5 A B Occasionally, debris may become lodged inside of the hose at the converter end (A). To clean out the hose, lift bottom of converter clip (B) with a screwdriver and remove clip. Remove debris as shown. Snap clip back into position making sure solution hose (C) is not pinched and moves freely. How to attach hose Disconnect carpet cleaner from electrical outlet. 3-6 C 1. To prevent possible leaking, remove clean solution tank by pressing down on tank handle (C) and pulling forward; set tank aside (do not set tank on furniture). Remove hose from storage rack. 3-7 3-8 3-9 D 2. Step on handle release pedal (D) and lower carpet cleaner handle until it rests on the floor. Unlatch back part of recovery tank and remove lid. 3. Remove recovery tank front panel (E) by sliding it straight up. 4. Replace panel with converter (F). Slide converter halfway down opening until it is firmly in place. Continued ➜ 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
11
Remove attachment from nozzle and rinse
in clear water.
Do not remove plastic
screen or foam from attachment.
A. Powered hand tool
has rotating brush-
es for extra scrubbing action on small carpet
areas, carpeted stairs and upholstery.
B. Stair/upholstery nozzle
has a built-in
brush to help provide the scrubbing action
some spots may need for removal.
How to attach tool
All tools connect to the hose in the same
manner.
1. Attach tool to connector end of hose by
sliding it onto connector until the tab (I)
locks it securely.
Using your thumb,
push forward and up
on the
latch (J)
to remove tool as shown.
Before using tool
It may be necessary to remove air from the
system (“prime the pump”) so the clean
solution will flow to the tool. Follow these
steps:
1. Attach tool to hose and turn the carpet
cleaner ON.
2. Put the tool on a hard surface or against
your hand to block off the suction.
3. Wait a few seconds (can take up to 15 sec-
onds). Then squeeze the trigger and begin
cleaning.
Follow the instructions on pages 13 and 14
for the appropriate cleaning task.
5. Drain solution tube by placing round end
in sink and raising nozzle above your head.
Press the trigger.
6. Proceed with steps c, d and e for “After
cleaning” on page 9.
Occasionally, debris may become lodged
inside of the hose at the converter end (A).
To clean out the hose, lift bottom of con-
verter clip (B) with a screwdriver and
remove clip. Remove debris as shown.
Snap clip back into position making sure
solution hose (C) is not pinched and moves
freely.
Using the tools
3-5
3-6
3-7
C
B
A
D
How to attach hose
Disconnect carpet cleaner from elec-
trical outlet.
1. To prevent possible leaking, remove clean
solution tank by pressing down on tank
handle (C) and pulling forward; set tank
aside (do not set tank on furniture).
Remove hose from storage rack.
2. Step on handle release pedal (D) and
lower carpet cleaner handle until it rests on
the floor.
Unlatch back part of recovery tank and
remove lid.
3-8
3. Remove recovery tank front panel (E) by
sliding it straight up.
3-9
4. Replace panel with converter (F). Slide
converter halfway down opening until it is
firmly in place.
Continued
➜