Hoover FH51000 Product Manual - Page 14

Warning, Caution - power cord

Get Hoover FH51000 PDF manuals and user guides View all Hoover FH51000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3. general operation remove and replace clean water solution tank ! CAUTION ! Do not fill with water above 140°F (60°C). 3.1 A 3.1 Press Clean Water Solution Tank button on handle (A). Tilt Clean Water Solution Tank away from cleaner and B remove (B). 3.2 Rotate measuring cap counter-clockwise from the top of Clean Water Solution Tank and pull up to remove. 3.3 Fill Clean Water Solution Tank with hot tap water to fill line. 3.4 Fill measuring cap with cleaning solution 3 times, (approximately 3 oz.). Pour into clean water solution tank and replace measuring cap. 3.3 3.5 Place clean water solution tank back on handle until it snaps in. NOTE: Using more than the recommended amount of cleaning solution may cause excessive foaming. ! CAUTION ! DO NOT USE THIS EXTRACTOR AND ACCESSORIES ON HARD FLOORS. USING THIS MACHINE ON HARD FLOORS MAY SCRATCH OR DAMAGE YOUR FLOOR. ! CAUTION ! Do not clean over floor electrical outlets. 3.5 ! WARNING ! To reduce the risk of fire and electric shock due to internal component damage, use only HOOVER® cleaning fluid intended for use with the appliance. Carpet Cleaning 3.6 Plug cord into electrical outlet. Step on handle release pedal, to put unit in cleaning position. 3.7 Step on power switch to turn machine ON (I=ON). 3.8 Squeeze trigger (C) to apply cleaning solution and slowly push cleaner forward (equals one wet stroke). Continue to squeeze trigger and slowly pull cleaner back toward you (second wet stroke). 3.9 Release trigger and slowly push cleaner forward over area just sprayed with solution (dry stroke). Then slowly pull cleaner back toward you without squeezing trigger (dry stroke). Continue using dry strokes until little water is visible passing through the nozzle (Pass over the same area a minimum of 4 times = 2 while squeezing the trigger and 2 without). For spots and high traffic areas use CLEAN BOOST™. To use CLEAN BOOST™ to remove those tough stains, apply extra cleaning solution by squeezing the trigger as you normally would and also pressing the Clean Boost™ trigger at the same time. NOTE: For best results, use straight, parallel strokes. Overlap strokes by 1 inch to help prevent streaking. 3.7 3.9 7 3.2 3.4 3.6 3.8 C ! CAUTION ! Detergents contain Anionic and Nonionic Surfactants. Avoid contact with eyes and skin. In case of contact with eyes, flush with cold water for 15 minutes. In case of contact with skin, wash with water. If irritation persists, call a physician.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
7
3. GENERAL OPERATION
3.1
REMOVE AND REPLACE CLEAN WATER SOLU-
TION TANK
3.1 Press Clean Water Solution Tank button on handle (A).
Tilt Clean Water Solution Tank away from cleaner and
remove (B).
3.2 Rotate measuring cap counter-clockwise from the top of
Clean Water Solution Tank and pull up to remove.
3.3 Fill Clean Water Solution Tank with hot tap water to fill
line.
3.4 Fill measuring cap with cleaning solution 3 times,
(approximately 3 oz.). Pour into clean water solution tank
and replace measuring cap.
3.5 Place clean water solution tank back on handle until it
snaps in.
3.2
3.4
NOTE:
Using more than the recommended amount of
cleaning solution may cause excessive foaming.
3.3
3.5
B
A
DO NOT USE THIS EXTRACTOR AND ACCESSORIES ON
HARD FLOORS. USING THIS MACHINE ON HARD FLOORS
MAY SCRATCH OR DAMAGE YOUR FLOOR.
Do not clean over floor electrical outlets.
WARNING
To reduce the risk of fire and electric shock due to internal
component damage, use only HOOVER
®
cleaning fluid
intended for use with the appliance.
CARPET CLEANING
3.6 Plug cord into electrical outlet. Step on handle release
pedal, to put unit in cleaning position.
3.7 Step on power switch to turn machine ON (I=ON).
3.8 Squeeze trigger (C) to apply cleaning solution and slowly
push cleaner forward (equals one wet stroke). Continue to
squeeze trigger and slowly pull cleaner back toward you
(second wet stroke).
3.9 Release trigger and slowly push cleaner forward over
area just sprayed with solution (dry stroke). Then slowly pull
cleaner back toward you without squeezing trigger (dry
stroke). Continue using dry strokes until little water is visible
passing through the nozzle (Pass over the same area a
minimum of 4 times = 2 while squeezing the trigger and 2
without).
For spots and high traffic areas use CLEAN BOOST
™
. To use
CLEAN BOOST
™
to remove those tough stains, apply extra
cleaning solution by squeezing the trigger as you normally
would and also pressing the Clean Boost™ trigger at the
same time.
NOTE: For best results, use straight, parallel strokes.
Overlap strokes by 1 inch to help prevent streaking.
3.7
3.8
3.9
3.6
C
CAUTION
!
!
CAUTION
!
!
CAUTION
!
!
!
!
Do not fill with water above 140°F (60°C).
CAUTION
!
!
Detergents
contain Anionic
and
Nonionic
Surfactants.
Avoid contact with eyes and
skin. In case of contact with
eyes, flush with cold water
for 15 minutes. In case of
contact with skin, wash with
water. If irritation persists, call
a physician.