Hunter 44660 User Guide - Page 12

On the back of the thermostat, find Switch SW1 at the lower

Get Hunter 44660 PDF manuals and user guides View all Hunter 44660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

12 ■ On the back of the thermostat, find Switch SW1 at the lower right-hand corner. 1) If your system is a gas furnace, then position the switch to HG. 2) If your system is an electric furnace, then position the switch to HE. 3) If your system is a single stage heat pump, then position the switch to SSHP. ■ Insert the upper tabs on the thermostat body into the slot at the top of the wallplate. Press bottom of the thermostat body to snap it into the wallplate. (NOTE: Do not force the thermostat onto the wallplate, as the terminal pins may be damaged. If it does not snap properly, the thermostat may not work.) ■ Switch on the main power at the panel or furnace. If you have not already programmed your thermostat, refer to page 13 to start setting up your programs. Page 34 will show you how to bypass the thermostats programming and activate temporary or permanent holds. See page 37 for other available options the thermostat has to offer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
12
■
On the back of the thermostat, find Switch SW1 at the lower
right-hand corner.
1) If your system is a gas furnace, then position the
switch to HG.
2) If your system is an electric furnace, then position the
switch to HE.
3) If your system is a single stage heat pump, then
position the switch to SSHP.
■
Insert the upper tabs on the thermostat body into the slot
at the top of the wallplate. Press bottom of the thermostat
body to snap it into the wallplate. (NOTE: Do not force the
thermostat onto the wallplate, as the terminal pins may be
damaged. If it does not snap properly, the thermostat may not
work.)
■
Switch on the main power at the panel or furnace.
If you have not already programmed your thermostat, refer to
page 13 to start setting up your programs.
Page 34 will show you how to bypass the thermostats
programming and activate temporary or permanent holds.
See page 37 for other available options the thermostat has to
offer.