Hunter 44660 User Guide - Page 48

Solution cont., Problem cont. - error

Get Hunter 44660 PDF manuals and user guides View all Hunter 44660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

48 Problem (cont.) Solution (cont.) HEATING OR COOLING DOES NOT GO ON OR OFF 1. Check that the system selector key is in the correct position ("HEAT," "COOL" or "AUTO"). 2. The thermostat may be in the AUTO mode. Look for "AUTO" on the LCD display. If the Heat and Cool program temperatures are close, then the thermostat requires a larger room temperature change before changing from Heat or Cool. 3. There may be as much as a 4 minute delay before the Heat or Cool system turns On - wait and check. (Compressor protection delay.) 4. Check your circuit breakers and switches to ensure there is power to the system. 5. Replace batteries. 6. Make sure your furnace blower door is closed properly. 7. Check the position of the Heat Pump switch. ERRATIC DISPLAY 1. Press the RESET button once with a small pin and hold for two seconds. The thermostat will need to be re-programmed. IF UNIT CONTINUES TO OPERATE 1. Replace unit. IN THE OFF POSITION THERMOSTAT PERMANENTLY READS "HI," "LO," OR "Error" AFTER PRESS- 1. Replace unit. ING RESET BUTTON If you experience any other problems, call 888-830-1326 for Technical Assistance from 7 AM to 7 PM Central Time Monday thru Friday and 8 AM to 5 PM Central Time on Saturday.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
48
1. Check that the system selector key is in the correct position (“HEAT,”
“COOL” or “AUTO”).
2. The thermostat may be in the AUTO mode. Look for “AUTO” on the
LCD display. If the Heat and Cool program temperatures are close,
then the thermostat requires a larger room temperature change be-
fore changing from Heat or Cool.
3. There may be as much as a 4 minute delay before the Heat or Cool
system turns On - wait and check. (Compressor protection delay.)
4. Check your circuit breakers and switches to ensure there is power to
the system.
5. Replace batteries.
6. Make sure your furnace blower door is closed properly.
7. Check the position of the Heat Pump switch.
1. Press the RESET button once with a small pin and hold for two sec-
onds. The thermostat will need to be re-programmed.
1. Replace unit.
1. Replace unit.
Solution (cont.)
Problem (cont.)
HEATING OR COOLING DOES
NOT GO ON OR OFF
If you experience any other problems, call 888-830-1326 for Technical Assistance from 7 AM to 7 PM Central
Time Monday thru Friday and 8 AM to 5 PM Central Time on Saturday.
ERRATIC DISPLAY
IF UNIT CONTINUES TO OPERATE
IN THE OFF POSITION
THERMOSTAT PERMANENTLY READS
“HI,” “LO,” OR “Error” AFTER PRESS-
ING RESET BUTTON