Home » Husqvarna Manuals » Lawn Mowers » Husqvarna TS142L » Manual Viewer

Husqvarna TS142L Owner Manual - Page 13

Caution, Warning

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

CAUTION: Do not operate the starter continuously for more than 15 seconds for each minute. 9. When the engine has started, slowly push in the choke control until the engine runs smoothly. When the engine operates smoothly, the attached equipment can be operated and you can operate the forward and rearward drive. Note: If the engine runs roughly, pull the choke control out for a few seconds and then continue to push the choke control in slowly. Note: If the engine does not accept the load, restart the engine and let it warm up for one minute. Follow the instructions above. To start a cold engine 1. Sit in the seat. 2. Make sure that the cutting deck is disengaged. Refer to To engage and disengage the cutting deck on page 16. 3. Put the cutting deck in transport position. Refer to To set the cutting deck in transport position or mow position on page 14. 4. Move the throttle control to the middle throttle position. 5. Pull out the choke control. CAUTION: If the ambient temperature is less than 40° F (4° C), you must let the engine operate 1 minute at idle speed before you operate the product. This is to let the transmission warm up. Make sure that the brake pedal is fully released. 10. Push in the choke control slowly. To start the engine when the battery is weak WARNING: Lead-acid batteries can make explosive gases. Keep sparks, flames and smoking materials away from batteries. Always wear eye protection when around batteries. If the battery is too weak to start the engine, it must be charged. If the jumper cables are used for emergency starting, follow the procedures below: A B C D 6. Push down on the brake pedal fully and keep it pushed down. 7. Put the ignition key into the ignition. 8. Turn the ignition key to the "START" position and release the ignition key when the engine starts. CAUTION: Do not operate the starter continuously for more than 15 seconds for each minute. Note: If the engine does not start after some tries, push the choke control in and wait some minutes before you try again. 9. When the engine starts, move the throttle control to the fast position to warm up the engine. If the temperature is low, some minutes is necessary for the engine to get warm. 1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery (B-C). CAUTION: Be careful that a short circuit does not occur against the chassis of the product. 2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal (D) of a fully charged battery. 3. Connect the other end of the BLACK cable (A) to good chassis ground, away from the fuel tank and battery. 4. Remove the BLACK cable from the chassis when the weak battery is fully charged. 5. Remove the BLACK cable from the fully charged battery. 6. Remove the RED cable from the two batteries. To remove the jumper cables Note: Remove the jumper cables in the opposite sequence to how you connect them. 1958 - 002 - 12.10.2022 13

Section	Page
Contents	2
Introduction	2
Pre-delivery inspection and product numbers	2
Product description	2
Intended use	2
Support / Help	2
Product overview	3
Symbols on the product	3
Hour meter	5
Product liability	5
Safety	5
Safety definitions	5
Safe Operation Practices for Ride-On Mowers	6
Safety instructions for operation	7
Personal protective equipment	7
Safety devices on the product	7
To do a check of the operator presence control (OPC)	7
To do a check of the reverse operation system (ROS)	7
To do a check of the brake	8
Parking brake	8
Muffler	8
To do a check of the muffler	8
To cut grass on slopes	8
Fuel safety	9
Battery safety	9
Transport safety	9
Safety instructions for maintenance	9
Assembly	10
Introduction	10
To remove the product from the carton	10
Assembly tools	10
Loose parts that need assembly	10
To install the lower cover	10
To adjust the seat	11
To connect the battery	11
To move the product off the skid	11
To do a check after the assembly	12
Operation	12
Introduction	12
To fill fuel	12
To start the product	12
To do before you start the product	12
To start a warm engine	12
To start a cold engine	13
To start the engine when the battery is weak	13
To remove the jumper cables	13
To set the cutting deck in transport position or mow position	14
To set the cutting height	14
To move forward and rearward	14
To engage and disengage the parking brake	14
To stop the product	14
To use the throttle control	15
To use the choke control	15
To use the cruise control	15
To use the headlight	15
To use the reverse operation system (ROS)	16
To engage and disengage the cutting deck	16
To get a good cutting result	16
To put the product in freewheel mode	17
To install the mulch plug (accessory)	17
To install the rear discharge deflector (accessory)	17
To install the grass catcher (accessory)	17
Maintenance	17
Introduction	17
Maintenance schedule	18
Lubrication schedule	19
Tractor	20
To clean the product	20
To use the deck washout port	20
To adjust the throttle control cable	21
To examine the interlocks and the relays	21
To replace the headlight bulb	21
To repair the tires	21
To do a check of the tires	21
To examine the V-belts	21
To do maintenance on the transaxle cooling fan	21
To examine the transaxle pump fluid	22
To adjust the front wheel toe-in and camber	22
To replace the fuse	22
To remove and install the engine cover and the grill assembly	22
To replace the drive belt	22
Battery	22
To clean the battery and the terminals	22
To replace the battery	23
To connect the jumper cables	23
To remove the jumper cables	23
Cutting deck	24
To remove and install the cutting deck	24
To adjust the parallelism of the cutting deck	24
To do a visual side to side adjustment of the cutting deck	24
To do a precision side to side adjustment of the cutting deck	24
To do front to rear adjustment of the cutting deck	25
To replace the blades	25
To remove the drive belt for the cutting deck	26
To install the drive belt for the cutting deck	26
To adjust the anti-scalp rollers	26
Engine	27
To lubricate the engine	27
To do a check of the engine oil level	27
To replace the engine oil	27
To replace the engine oil filter	28
To clean the air filter	28
To clean the air screen	28
To do maintenance on the engine cooling system	28
To replace the spark plugs	28
To replace the in-line fuel filter	28
To remove the air from the transmission	28
Troubleshooting	29
Transportation, storage and disposal	34
Transportation	34
Tow safety	34
Storage	34
Disposal	35
Technical data	35
Service	36
Service	36
Contenido	37
Introducción	37
Inspección previa a la entrega y números de producto	37
Descripción del producto	37
Uso previsto	37
Soporte/ayuda	37
Descripción general del producto	38
Símbolos en el producto	38
Medidor de horas	40
Responsabilidad del fabricante	40
Seguridad	40
Definiciones de seguridad	40
Prácticas de uso seguro para cortacésped	41
Instrucciones de seguridad para el funcionamiento	42
Equipo de protección personal	42
Dispositivos de seguridad en el producto	42
Para verificar el control de presencia del operador (OPC)	43
Para verificar el sistema de funcionamiento en reversa (ROS)	43
Para comprobar el freno	43
Freno de estacionamiento	43
Silenciador	43
Para revisar el silenciador	43
Para cortar césped en pendientes	43
Seguridad de combustible	44
Seguridad de la batería	45
Seguridad del transporte	45
Instrucciones de seguridad para el mantenimiento	45
Montaje	46
Introducción	46
Para extraer el producto de la caja de cartón	46
Herramientas de montaje	46
Piezas sueltas que necesitan montaje	46
Para instalar la cubierta inferior	46
Para ajustar el asiento	46
Para conectar la batería	47
Para retirar el producto de la plancha	47
Para comprobar el montaje	47
Funcionamiento	48
Introducción	48
Para agregar combustible	48
Para poner en marcha el producto	48
Antes de arrancar el producto	48
Para arrancar un motor caliente	48
Para arrancar un motor frío	49
Para arrancar el motor cuando la batería tiene poca carga	49
Para retirar los cables de puente	49
Para colocar el equipo de corte en la posición de transporte o posición de corte	50
Ajuste de la altura de corte	50
Para mover hacia delante y hacia atrás	50
Para acoplar y desacoplar el freno de estacionamiento	50
Para detener el producto	51
Para utilizar el control del acelerador	51
Para utilizar el estrangulador	51
Para utilizar el control de crucero	51
Para usar el faro delantero	52
Para utilizar el sistema de funcionamiento en reversa (ROS)	52
Para acoplar y desacoplar el equipo de corte	52
Para conseguir un buen resultado de corte	52
Para poner el producto en modo de rueda libre	53
Para instalar el tapón de mantillo (accesorio)	53
Para instalar el deflector de descarga trasero (accesorio)	53
Para instalar el recogedor de césped (accesorio)	53
Mantenimiento	54
Introducción	54
Programa de mantenimiento	54
Programa de lubricación	55
Tractor	56
Para limpiar el producto	56
Para utilizar el puerto de lavado del equipo	56
Para ajustar el cable del acelerador	57
Para revisar los enclavamientos y los relés	57
Para reemplazar la bombilla del faro	57
Para reparar los neumáticos	57
Para comprobar los neumáticos	57
Para examinar las correas en V	57
Para realizar mantenimiento en el ventilador de refrigeración del transeje.	58
Para examinar el líquido de la bomba del transeje	58
Para ajustar la convergencia y la inclinación de la rueda delantera	58
Para reemplazar el fusible	58
Para quitar e instalar la cubierta del motor y el conjunto de parrilla	58
Para reemplazar la correa de transmisión	58
Batería	59
Para limpiar la batería y los terminales	59
Para reemplazar la batería	59
Para conectar los cables de puente	60
Para retirar los cables de puente	60
Equipo de corte	60
Para quitar e instalar el equipo de corte	60
Para ajustar el paralelismo del equipo de corte	61
Para realizar un ajuste visual de lado a lado del equipo de corte	61
Para realizar un ajuste preciso de lado a lado del equipo de corte	61
Para realizar el ajuste de adelante hacia atrás del equipo de corte	62
Para sustituir las hojas	62
Para retirar la correa de transmisión del equipo de corte	63
Para instalar la correa de transmisión del equipo de corte	63
Para ajustar las ruedas de apoyo	63
Motor	64
Para lubricar el motor	64
Para revisar el nivel de aceite del motor	64
Para cambiar el aceite del motor:	64
Para reemplazar el filtro de aceite del motor	65
Para limpiar el filtro de aire	65
Para limpiar la pantalla de aire	65
Para realizar mantenimiento en el sistema refrigerante del motor	65
Para reemplazar las bujías	66
Para reemplazar el filtro de combustible en línea	66
Para extraer el producto desde la transmisión	66
Solución de problemas	67
Transporte, almacenamiento y eliminación de residuos	73
Transporte	73
Seguridad de remolque	73
Almacenamiento	73
Eliminación	74
Datos técnicos	74
Servicio	75

Match case Limit results 1 per page

CAUTION:

Do not operate the

starter continuously for more than 15

seconds for each minute.

When the engine has started, slowly push

in the choke control until the engine runs

smoothly. When the engine operates smoothly,

the attached equipment can be operated and you

can operate the forward and rearward drive.

Note:

If the engine runs roughly, pull the choke

control out for a few seconds and then continue

to push the choke control in slowly.

Note:

If the engine does not accept the load,

restart the engine and let it warm up for one

minute. Follow the instructions above.

To start a cold engine

Sit in the seat.

Make sure that the cutting deck is disengaged.

Refer to

To engage and disengage the cutting

deck on page 16

Put the cutting deck in transport position. Refer

To set the cutting deck in transport position or

mow position on page 14

Move the throttle control to the middle throttle

position.

Pull out the choke control.

Push down on the brake pedal fully and keep it

pushed down.

Put the ignition key into the ignition.

Turn the ignition key to the “START” position and

release the ignition key when the engine starts.

CAUTION:

Do not operate the

starter continuously for more than 15

seconds for each minute.

Note:

If the engine does not start after some

tries, push the choke control in and wait some

minutes before you try again.

When the engine starts, move the throttle control

to the fast position to warm up the engine. If the

temperature is low, some minutes is necessary

for the engine to get warm.

CAUTION:

If the ambient

temperature is less than 40° F (4°

C), you must let the engine operate

1 minute at idle speed before you

operate the product. This is to let the

transmission warm up. Make sure

that the brake pedal is fully released.

10. Push in the choke control slowly.

To start the engine when the battery is

weak

WARNING:

Lead-acid batteries can

make explosive gases. Keep sparks,

flames and smoking materials away from

batteries. Always wear eye protection

when around batteries.

If the battery is too weak to start the engine, it must

be charged.

If the jumper cables are used for emergency starting,

follow the procedures below:

Connect one end of the RED cable to the

POSITIVE (+) terminal of each battery (B-C).

CAUTION:

Be careful that a

short circuit does not occur against

the chassis of the product.

Connect one end of the BLACK cable to the

NEGATIVE (-) terminal (D) of a fully charged

battery.

Connect the other end of the BLACK cable (A)

to good chassis ground, away from the fuel tank

and battery.

Remove the BLACK cable from the chassis when

the weak battery is fully charged.

Remove the BLACK cable from the fully charged

battery.

Remove the RED cable from the two batteries.

To remove the jumper cables

Note:

Remove the jumper cables in the opposite

sequence to how you connect them.

1958 - 002 - 12.10.2022