IBM 4800-741 Operation Guide - Page 101

Installing, large, table, mount, pedestal

Get IBM 4800-741 PDF manuals and user guides View all IBM 4800-741 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Updated October 31, 2007 2. If you plan to position the mounting plate under the cash drawer (for an integrated appearance), install the three extra feet as follows (see Figure 79 on page 80) : a. Attach one on each of the front cash-drawer feet. b. Attach one on the rear cash-drawer foot opposite the display. Note: Cables will be routed down the post and out the back under the cable cover. Installing the large CRT table post mount to a pedestal Follow these steps to attach the pedestal to the large CRT table post mount: B A Figure 80. Attaching the short CRT post mount to the large CRT table post mount 1. Verify that the panel is installed at position A in Figure 80. 2. Place the large CRT table post mount upside down on the counter. Attach the short CRT post mount to the two center holes of the large CRT table post mount and attach with two screws B . 3. If you are using a short post and a mounting plate, install it now. See "Attaching the pedestal to the short-post mounting plate" on page 80. 4. If the post is going to be installed to the counter, install it now. See "Attaching the distributed pedestal to the counter" on page 78. 5. Route the power cables and the video cables down through the pedestal. 6. Attach the cables to the appropriate port in the system unit. Attention: Secure the front and back of the base of the CRT with two large tie-wraps. Route the tie-wrap up through the slot, over the top of the CRT base, and down through the other slot. Secure the tie-wrap and cut the excess tie-wrap flush on the end. Repeat this procedure to secure the front and back of the CRT. Chapter 4. Installing external options 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
2.
If
you
plan
to
position
the
mounting
plate
under
the
cash
drawer
(for
an
integrated
appearance),
install
the
three
extra
feet
as
follows
(see
Figure
79
on
page
80)
:
a.
Attach
one
on
each
of
the
front
cash-drawer
feet.
b.
Attach
one
on
the
rear
cash-drawer
foot
opposite
the
display.
Note:
Cables
will
be
routed
down
the
post
and
out
the
back
under
the
cable
cover.
Installing
the
large
CRT
table
post
mount
to
a
pedestal
Follow
these
steps
to
attach
the
pedestal
to
the
large
CRT
table
post
mount:
1.
Verify
that
the
panel
is
installed
at
position
±A²
in
Figure
80.
2.
Place
the
large
CRT
table
post
mount
upside
down
on
the
counter.
Attach
the
short
CRT
post
mount
to
the
two
center
holes
of
the
large
CRT
table
post
mount
and
attach
with
two
screws
±B²
.
3.
If
you
are
using
a
short
post
and
a
mounting
plate,
install
it
now.
See
“Attaching
the
pedestal
to
the
short-post
mounting
plate”
on
page
80.
4.
If
the
post
is
going
to
be
installed
to
the
counter,
install
it
now.
See
“Attaching
the
distributed
pedestal
to
the
counter”
on
page
78.
5.
Route
the
power
cables
and
the
video
cables
down
through
the
pedestal.
6.
Attach
the
cables
to
the
appropriate
port
in
the
system
unit.
Attention:
Secure
the
front
and
back
of
the
base
of
the
CRT
with
two
large
tie-wraps.
Route
the
tie-wrap
up
through
the
slot,
over
the
top
of
the
CRT
base,
and
down
through
the
other
slot.
Secure
the
tie-wrap
and
cut
the
excess
tie-wrap
flush
on
the
end.
Repeat
this
procedure
to
secure
the
front
and
back
of
the
CRT.
B
A
Figure
80.
Attaching
the
short
CRT
post
mount
to
the
large
CRT
table
post
mount
Updated
October
31,
2007
Chapter
4.
Installing
external
options
81